Thanks! I'd have dug in for a look by now if not recovering from rotator cuff repairs. 73, Bob AH7I/W4 _______________________________________________ TenTec mailing list TenTec@contesting.com http:
Aloha all and happy new year! Ten Tec 1. Eagle accessory connector manufacturers PN? I'd like to order a couple. 2. Any word on updated Eagle schematics? 3. Turn off the Eagle AGC? 4. 565/566 top and
I always have trouble with the attack when fixing my own stuff while having no problem with ideas for other peoples stuff...so here goes.... My first suspect, based on what you have done so far, woul
Phil If you have stuff lying around, it's gonna be cheap and fast to make up a cable. Last night I made up a cable for the Eagle. Took about 15 min. I used the three circuit audio/video cable scroun
Any suggestions? I'm thinking 3 SPST reed relays . One to switch the Tx antenna. One to switch detuner for the Tx antenna. One to switch the Rx antenna. The reed relays switch in ~1ms so the 17ms tra
In case the sketch on my earlier email was stripped.... To clarify... I want to work CW break in on 160/80/40. I can not use my TX antenna for RX on 160 and 80. Urban Atlanta is much to noisy. I'm in
Decided. I'm going with the three relay solution. I found some "reed" type relays with specified ~1ms switch times and 10^7 cycles lifetime. All SPST. When receiving, power will be applied to the rel
Dwight I don't know the Corsair but based on it's age... Perhaps component value changes. In some of my older tube gear it has led to poor stability of a heterodyne xtal oscillator. You can check if
Finally got to spend a little time on it. Sub-receiver not working so no MWBCB. Still need to test TX on SSB. Otherwise seems OK. Need speaker and sheet metal parts. Not sure of details. Attached vid
Airpax part http://www.onlinecomponents.com/airpax-sensata-t111200a0111cv.html?p=10094595 show 20 in stock. 73, -Bob ah7i _______________________________________________ TenTec mailing list TenTec@co
Paul If you want to try your hand with a SMT kit, Try the Si570 kit: http://www.qsl.net/k5bcq/Kits/Kits.html $44. including postage. Not drop in but if you like messing around with electronics, you c
What's the Dallas PN? Website illustrates procedure similar to our 'fix' for Sun work stations. http://www.tns-soft.com/nvram.html IIRC, we'd cut a notch on the top near the end, popped the short par
Aloha Jims (OCG and KGI)- On the antenna topic. I was using a 10m(33') vertical folded dipole made/fed with 300 Ohm TV twinlead(1.6 cents a foot at Radio Shack sale) and found the same. It worked wel
I don't have an Omni VI. I have an ill Eagle that's still under warranty. Looked at the manual and read that the keying waveform is adjustable via R24 on the control board. Also that the T/R keying i
Peg You wrote: "The Ten-Tec website carries a USB - Serial Converter Cable but says it doesn't work with the Eagle, which we also have in the shack. Out of curiosity, is this because the Eagle has a
Sorry, forgot the subject line _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
John Thanks! OmniRig works great with the 599 and HDSDR. TenTec USB -> serial purchased with a RX320(pre-D) is still going strong in another application. Do the 599 and the 539 use the same 9MHz tap
Facts: There are over 7 billion people on this planet! There are more than 3.5 billion people on this planet who do not understand the metric system! Testimonials: Ben Livingston writes, "I was visit
Kris Are these 811 or 572? I've never owned a Centaur but have not had any trouble with non-matched tubes in other amps, provided they were from the same OEM. A single used 811 or 572 should be prett