I assume you mean the DX777 Headset. I've been using one with my Orion II & Omni VII for a long time & love it. I haven't done anything to the settings in the rig & get excelloent results with great
Thanks, John. My bad 73 Dave -- Original Message -- No Dave, the DX777 is a normal multi-ear piece set, the DX767 is a single ear-piece set. John de VK2XGJ If you can't fix it with a hammer, then yo
I've got 2 & love them, but am considering selling one or both as I also love the Orion II & the Omni VII Dave WA3F -- Original Message -- I think the ergonomics of the Omni 6+ are unmatched. If you
Rick, When I had Paragon 1's I routinely replaced the 9-volt rechable batteries with Radio Shack 9- volt rechargeables and they worked just fine. Be aware that for the battery to recharge early Parag
Rick, You are 100% correct about the TenTec supplied cable for the FSK lead. The cable provided is the same as for the Omni VII. Unfortunately, when the Orion II was designed (I have both Orion II &
Thanks, Bob. The simple thing would have been to put the FSK on pin 5 of the 8-pin connector when the Orion was designed. I know this sounds simple, but I'm sure there was an engineering reason for t
-- Net Plans AM Night Dec. 27 Dec 4 Written by: Paul McLane 12/4/2012 12:37 PM I have a note here that will be of interest to many broadcast engineers past and present. The Greater Cincinnati Amate
I had it on all 3 of my Omni VI+. It is well worth the price 73 Dave WA3F -- Original Message -- From: "Paul Kraemer" <elespe@lisco.com> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
I am keying my CW from an RS-232 port, and my PTT line when using RTTY FSK from an RS-232 port The rig is an Orion II My interface from the RS-232 to the Orion II is an Opto-Isolator (I use the W3YY
Thanks, Lee. This morning I drew the circuit and it all made sense. I just had to see it and have a sanity check. For some reason, when it was not drawn, I had a problem with separate grounds coming
Check your manual for the DIN jack. Mine is item #80 on page 28 & it states that Pin 4 of the DIN connector is 'line level audio output. Which receiver(s) are output to here and the level of audio se
The 'OTHER' menu provides a setting of High, Medium or Low for the Line Level Output 73 Dave WA3F -- Original Message -- From: "Michael Cheponis" <Michael@Cheponis.Com> To: "Discussion of Ten-Tec Equ
Absolutely. I sold oneof mine because I have an Omni VII and an Orion II, but I swtill kept one. I should part with it, but that's not in the near term. They are great rigs. I don't think I've worked
It's a perfect candidate for the 715 speech processor. That's where I used mine. Don't do much SSB, and none on the VI+, so that's on the shelf. 73 Dave WA3F -- Original Message -- From: "Bob McGraw
PS = 961 or 962 Mic = 705 Amp = Herc II, Titan or Centurian Auto Tuner = 253 Tuner = 238 73 Merry Christmas Dave WA3F -- Original Message -- From: "Bry Carling" <bcarling@cfl.rr.com> To: TenTec@yahoo
I need a TenTec 311 Band Decoder and the cable that shipped with it. Anybody got a spare or one they're not using I can pay via PayPal, personal check (yeah, I know I'll have to wait for it to clear)
Gary, Thanks for the reply. I do have a schematic of the 311, so I can build one if necessary. Of course, the most difficult part will be cross-referencing all the surface mount compononts to 'real'
Gary, I can't believe it. Yesterday I got an e-mail and a 311 is on the way. I did scan your project and will read it in more depth next week. With the availaboilty of N1MM to give me band data, I ma
If Rick doessn't do it, I will. It is easy to make inexpensive open wire lines with 1/2" flexible PVC (about $20 for 100 ft. at Home Depot) for the spacers that it or window line should be on any ant
I have a TenTec 715 RF Speech Processor in like-new condition. I am the original owner and it has lived in a non-smoking home. I used this Speech Processor with my Omni VI+s and with my Omni VII. I n