HiI'm trying to upgrade my Ver. 1.839 firmware to the latest version 2.xxx. I am still having a time finding two things: 1. where the new version 2 .inf file can be found to download 2. where I can f
I am not a purist. I do however get excited about alternative successful optional methods when it involves saving money, time or length of repairs, or longevity of the repair. The issue I am thinking
The Tri-Flo is in a black spray can and does contain the silicone balls in the lubricant. 73 de Dave in NH. K1OPQ How you were Sent from my iPhone _______________________________________________ TenT
Doing a system reset: Power on and hold MNU key, it doesnt boot completely. All the encoders report as working, all the pushbuttons report being pressed, but the display doesnt go beyond when OMNI VI
I must have hit a dead spot on the reflector having heard only one reply, thanks Mike. I will adjust my thinking. Having done a system reset: Power on and hold MNU key, my OMNI VII continues to not b
HiI have an OMNI VI that started to fail; the readout began to flash and the relay on the DC power board (about 2.5" square) began buzzing. I replaced the 1000uF cap @ 25V with one of the same cap. b
Hi AllI have a fine OMNI VI that has an issue that Id like to solve: The frequency readout and transmit frequency do not agree with my OMNI VII, K2 and two Optoelectronic frequency counters. They all
HiIs the 70 MHz IF in the OMNI VII available to tap to use with a SDR panadapter? If so ,can you point me in the right direction? Dave, K1OPQ _______________________________________________ TenTec ma
HiThanks all to those giving me some leads on locating the OMNI VII IF out connector. In short, I found that all that is needed is a mini coax about 11-1/2 long with TMP connectors at each end. The I
HiI am in search of a RG-174 coaxial cable 11-13 inches long with TMP connectors on both ends. It is used for many interstage connections. I know they are in an OMNI VI, probably the OMNI V as well.
HiStill my OMNI VI wont boot. A few weeks ago someone suggested a ham down the east coast toward Florida who does Ten Tec repairs. Anyone have a clue as to whom that would be? Thanks, 73 de Dave, K1O
I have a Ten-Tec OMNI VI that isnt working for sale. Cosmetically it is a 9++. It has the full complement of Roofing filters and the manual. $400 here in NH, shipping extra. Pictures available. _____
Hi- I am in search of a #81606 Ten-Tec logic board in good working condition as used in the OMNI VI. Thanks for looking. 73 de Dave, K1OPQ/4 Sent from my iPhone ______________________________________
Gents, Has any one run an Omni VI Plus with a TL-922A? I'm planning on acquiring a 922A and am wondering if there are any things I should be aware of in advance. == I had run my OMNI VI + and a TL922
I have a beautiful Centaur amp for sale. Covers 160-10 Meters TT QSK 3 new RF Parts 572B tubes. Pictures upon request. Not a scratch. Only update was to replace the Operate/Stanby switch with one a b
Hi I have had an opportunity to bring different T-T PTOs back into usefulness with out a total tear down. The silicone based lubricant has been available at Bicycle Shops. The name of the lubricant i
When I turn on my OMNI VI it takes between 30 - 60 seconds or more before the rig springs into life and starts receiving. During that time there is a low frequency audio that increases in volume and
I have both a Ten-Tee OMNI VII and an OMNI VI+ that are not being utilized. Both are loaded with filters and not a scratch. Both i excellent condition. Omni Vii is $850. Omni VI+ is $650. Located nea
This Omni Six show no physical signs of wear, salt water, tobacco or other enviromental abuse. It needs some help. It does come on, frequency changes, the S meter light does not work. After about a m
I have a Ten-Tec OMNI VI that is in excellent physical condition, a couple light scratches on the cabinet, the front panel is like new. It has the 2.4 and 1.8KHz filters. It almost works. At turn on