yep.. -- Original Message -- From: "Ed Purvis" <wa4njy_am@yahoo.com> To: <tentec@contesting.com> Sent: Friday, December 10, 2004 7:49 PM Subject: [TenTec] Corsair Microphone Can I use the 705/706 mic
The Corsair II...and I have one..does have a relay to key an amp.. However I would use a second relay between the rig and the amp just to be sure... -- Original Message -- From: "NJ0IP" <Rick@DJ0IP.d
Wonder how an Omni VI compares to a Corasir II in similar circumstances? thanks de Denton WB7TDG -- Original Message -- From: "WF2U" <wf2u@starband.net> To: <tentec@contesting.com> Sent: Sunday, Dece
Ok Steve...here is my situation... I have an old Corsiar II that I am using for casual listening with a 500 hrz cw filter.. I currently use a Pegasus for psk mostly, but I notice it sounds better to
Hi all... have recieved a new rigblaster plus and am hooking it to my Corasir II am using MixW for the program... com port is communicating with the rigblaster ok, but what jumper setting do I need t
Check the B+ fuse..near the power cord plug. -- Original Message -- From: "W.D. (Doc) Lindsey" <dock0evz@earthlink.net> To: "Ten-Tec Reflector" <tentec@contesting.com>; "QRP-L on QTH Net" <QRP-L@mail
pins 2 & 3 go to the power push pull knob in the front of the corsair and are only for turning a ten tec power supply on and off pin 1 is the B= pin 4 is ground, both chassis and power supply. with t
Hi Tim...when I got my corsair II a decade or so ago, if I recall I couldn't get my bug to work with the 1/4 stereo jack either...seemed to recall it had something to do with the keyer speed dial or
Hi Jan... I already noticed one little quirk....the Omni didn't want to do anything this morning until I punched one of the band register buttons...typical? -- Original Message -- From: <k7gt@charter
I have for sale a TT Pegasus, with manual and remote tuning knob. Rated power out on all bands. Have replaced the relays on the 20 meter bandpass filter side and installed a much huskier power cord.
Since I haven't gotten any other replies on this item, I am relisting it.. I notice that my used (new to me) Omni VI Plus upgraded to option 3 does not want to do anything when I turn it on in the mo
My stations power supply is always on. Since I had to tweek the alc and agc pots as output was running about 60 watts max, I reseated all the cabeling on both the bottom and top of the omni. 80 meter
I notice something rather funny up on 20 meter psk....the signals would at times kinda move a few hrz off feq and then drift right back on feq..kinda like someone bumping the main band tuning knob. I
I have an Omni VI plus...what does the rig have in it for current limiting?? Thanks.. -- Original Message -- From: "NJ0IP" <Rick@DJ0IP.de> To: <tentec@contesting.com> Sent: Thursday, January 13, 2005
I am also running an Omni VI plus..and using MixW I have had my best results running the sliders for play control and wave/mp3 wide open...and adjusting the mic gain on the rig to just below alc ligh
I until recently ran a Peg for psk.. Line out on front panel will suffice nicely for line in jack on the soundcard. This is a constant..regardless of audio setting for the speaker...level out. There
used to have a 580 Delta...es gud rig!! the slop in the band switch is caused by the knob not up to snuff...remove it with an allen wrench and you will see it is cracked where it attached to the band
Every Ten Tec I have ever owned I have pulled the real panel mount power socket and installed my own. See if you have enough room at the top or bottom of the power connector to snake thru a no. 12 or
I recently purchased a used Omni VI that quit transmitting, sent it in to TT for repair and alingment. TT replaced the finals and some other work... I recieved the repaired Omni yesterday and wasted