Hello, I friend borrowed me an Omni VI, which is producing very disturbing audio-clicks in fast QSK mode, at any CW speeds, even with very slow keying. The clicks are louder than the received signal
Barry, Are these fast QSK audio clicks on key up the default behavior for Omni VI rigs? I was thinking something could be wrong with this Omni in fast QSK. Tnx for letting me know. I have no prior ex
Thanks a lot Steve for pointing this posting out to me. Re-cabling and screening audio cables will certainly do know harm. This will be next on my todo list. So far I re-cabled the logic board (put c
Good point, Barry. The two ROMs are labeled "Option 1". 73 Gerd. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo
QRGs in log are used to verify un-assisted / no cluster contest entrants. The logged QRGs help understand how the op found multipliers, and why. See also disqualification discussions on this in the p
consider* Raspberry will be fine. Hardware: - Use Raspberry - Add dd frequency counter interface, along idea here http://www.swharden.com/wp/2016-10-10-raspberry-pi-rf-frequency-counter/ - Add bad d
Did some further poking into the the QSK clicks In slow QSK the RX audio comes back 60 msec after cw key up, as seen on scope. In fast QSK itīs abt. 5 msec or less Clicks also present with RF TX powe
Hello, Had a QSO with DJ5IL last year. He stated using the codephaser daily. As he put it: CW sounds boring without. I have one such codephaser ( http://www.cq-cq.eu/DJ5IL_rt001.pdf ) for sale. 30 EU
Hello, I used this speaker for my Omni 6: Visaton FR 8 https://www.buerklin.com/medias/sys_master/download/download/he9/hc6/8891373944862.pdf https://www.buerklin.com/en/full-range-speaker/p/38m682 I
Paul, have a loo at ist policy http://lists.contesting.com/mailman/listinfo/tentec DO NOT USE THIS LIST TO POST COMPLAINTS, PERSONAL CRITICISMS, ATTACKS, ETC. VIOLATORS OF THIS POLICY WILL BE REMOVED
Foto of Visaton FR 8 loudspeaker in Omni VI: https://drive.google.com/file/d/0B5pgZv7OnII7cmNJUWl1OXFLZ1E/view?usp=sharing Original mounting bolts removed 4 new screws placed to hold FR 8 73 Gerd. Vi
John, if you believe the problem is the XTALs then the first step would be to unsolder them and check / measure them? BR Gerd. _______________________________________________ TenTec mailing list TenT
Hello, Looking for an Omni VI voice synthesizer plug-in board or for the EPROM data so I could build my own voice board. 73 Gerd DF9TS _______________________________________________ TenTec mailing l
I have for sale a Ten-Tec Omni VI: Logic board ROM option 1 DSP Rom Option 1 Front panel buttons have been replaced, no stickers on buttons All four 6.3 MHz filters from Tentec 9 MHz Filter is Inrad
Hello Bill, is the Omni remote VFO kno still available? 73 Gerd. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo
Bill, I meant the 301 remote encoder for Omni VI.. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Hello Karl, I am using Wintest for CAT control of my Omni VI+ - it works flawlessly with a simple USB-to-serial adapter and also with the Microham CW keyer (set to RS232 levels) 73 Gerd DF9TS _______
Pete, could you share the procedure you mentioned? I have a OMNI VI that I love. PLL board has the two PLL circuits out of sync, I have no continous frequency output from VFO anymore. Checked and tri
It has taken a while since my original request almost 5 years ago in this list: "... Looking for an Omni VI voice synthesizer plug-in board or for the EPROM data so I could build my own voice board..
Ken, I just got the filter. Thanks again and all the best to you! Gerd DF9TS _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mail