Mail Archive Search: <+from:dnelsen@integraonline.com>

Results:

References: [ +from:dnelsen@integraonline.com: 8 ]

Total 8 documents matching your query.

1. Re: [TenTec] Omni-VI 2.8 KHz filters (score: 1): Author: dnelsen@integraonline.com; Date: Sat, 29 Jan 2005 18:09:31 -0800 (PST); _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec; /archives//html/TenTec/2005-01/msg01152.html (11,840 bytes)
2. Re: [TenTec] MODEL 219 Filter (score: 1): Author: dnelsen@integraonline.com; Date: Sun, 30 Jan 2005 18:07:36 -0800 (PST); Try checking the application table at INRAD's website. Dave AB0N _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinf; /archives//html/TenTec/2005-01/msg01178.html (7,540 bytes)
3. Re: [TenTec] Omni-D w/ power supply for sale (score: 1): Author: dnelsen@integraonline.com; Date: Wed, 16 Feb 2005 00:41:14 -0800 (PST); Most likely reason was that if the set screws were over tightened and the knobs cracked. My Omni-A suffered that fate. Much happier with the Radio Shack replacements. They have a brass center so no; /archives//html/TenTec/2005-02/msg00461.html (7,698 bytes)
4. Re: [TenTec] Paragon II display freezing up (score: 1): Author: dnelsen@integraonline.com; Date: Sat, 16 Apr 2005 21:35:07 -0700 (PDT); Hum in a power supply especially a vintage one would tend to imply the failure of the smoothing Cap. You may want to replace it as the ripple will only get worse. You should be able to locate a high; /archives//html/TenTec/2005-04/msg00443.html (9,328 bytes)
5. Re: [TenTec] Omni C (score: 1): Author: dnelsen@integraonline.com; Date: Thu, 16 Jun 2005 10:15:05 -0700 (PDT); Also consider changing the IC Op Amp in the AGC circuit. I think I liked the TI TL072 or 82. I'd have to look inside the rig to confirm what's there. This not a 100% cure but I found it to help on a; /archives//html/TenTec/2005-06/msg00435.html (8,376 bytes)
6. Re: [TenTec] Omni C (score: 1): Author: dnelsen@integraonline.com; Date: Thu, 16 Jun 2005 14:25:12 -0700 (PDT); Hi Bob, Checked my Omni-A. Found a Burr Brown OPA2604AP Dual Op amp in there. I did the experiment several years ago. As memory serves the TI chips were good but I liked the Burr Brown chip mentioned; /archives//html/TenTec/2005-06/msg00444.html (8,430 bytes)
7. Re: [TenTec] Looking for Century 22's calibrator and keyer optionboards (score: 1): Author: dnelsen@integraonline.com; Date: Fri, 19 Aug 2005 16:06:17 -0700 (PDT); Hi Jerry, I am converting to DDS VFO's and AADE frequency display on my original Omni-A model 545. If that calibrator will work? Let me know. We might work something out. The AADE is vastly superior; /archives//html/TenTec/2005-08/msg00363.html (8,505 bytes)
8. [TenTec] [Fwd: Ten Tec related items For Sale] (score: 1): Author: dnelsen@integraonline.com; Date: Fri, 11 Nov 2005 11:23:37 -0800 (PST); FS: Model 243 VFO with original manual. Works fine. Cosmetically 8.5 out of 10. Asking $110 + Shipping. FS: AADE DFD-1 Digital Readout in AADE's nice gray cabinet. Plugs into counter out on the Model; /archives//html/TenTec/2005-11/msg00195.html (7,786 bytes)

Current List: 1 - 8
Page: [1]