I have one spare Orion VFO encoder and 5 of the small encoders if anyone needs them. All are tested. VFO = $50 shipped Small = $25 shipped Gary W0DVN _______________________________________________ T
They are not as hard to replace as they look. I have one more left at $25 shipped. Gary _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesti
Ill commit to three to help with the price break. I have three Omni 6 radios... Gary W0DVN _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.conte
Since I need three myself, I am willing to lead this. I ownt place an order until I have payment to cover the cost for 10 of them. My only addition would be for the postage to mail them out so the fi
All of my Orion encoders are spoken for. Thanks to all, Gary PS: I am formalizing the quote and order for the Omni 6 reference oscillators and will post that I can accept purchase payments once the q
I personally wish you nothing but the best success. Gary W0DVN PS - I have been talking on some of the Omni 5/6 repairs that come down the road to me I still like working on them and would rather wor
Sounds like a failing CFL illuminator. LCD Parts can supply LED illuminator replacements and I can instruct you as to how to make the swap. Gary _______________________________________________ TenTec
The illuminators typically cost me $70 with the driver boards included. This board offers adjustable brightness. It runs from 12 volts power and has a line that you can interface with the existing br
I have fixed a few dozen of these too and have three parts cadavers. Gary W0DVN _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/m
Does anyone know of a source for the small black Torx screws for the back of the Orion? I need a set. Gary W0DVN _______________________________________________ TenTec mailing list TenTec@contesting.
I needed some of the black 4-40 TORX screws for an Orion I had. I was required to buy 100 to get what I need. They cost me $0.15 each. If you need any, you can have as many as you need for that price
Orion screws are sold. Gary _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Sounds like a compromised ground somewhere. The Omni 6 had plenty of digital noise. Ten Tec did a lot of good work putting grounds here and there, plus some insulator tape here and there to reduce th
What is wrong with your existing board? Gary _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
I did receive the TCXO reference oscillators for the Omni 6 I will be shipping to those who purchased them in the next day or so. You know, with some clever work, you could use these on an Omni 5 as
The schematic is not wrong. The circuit is not a full wave rectifier, it is a voltage doubler. That is why you see 140 DC from a 70m VAC transformer. Gary ____________________________________________
I have a complete board. $40 shipped in CONUSA. Gary _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Those may cause a problem, but that problem would have always been present. The thing could never have worked since, no one in their right mind would change the and the radio certainly would never ha
Note that the PTO signal first enters the Time Base board via the 2 pin connector. The PTO signal is shaped and sent to the actual counter board, along with the 5.24888 MHz reference via the 9 pin ca
PayPal dukeshifi@comcast.net Gary _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec