i have a paragon II coming anyday now - i see alot of ads for paragons with the geil chip - what are the advantages of upgrading to this firmware? - will i see a big difference in performance and wha
hi all, can i use a corsair 1 p.s. (260) to power a paragon II. the corsair has some control leads to shut the power supply, don't know if the paragon would shut the power suppy down or not - anyone
i recently purchased a really nice clean paragon II - going through the radio now and must say its a really nice radio - nice receive, good ergonomics. a couple of things i notice in my short time wi
ok correction - the radio only has the 6.0 and 2.4 khz filtyers installed - the PBT is working with the 2.4 khz filter, but not with the 6.0 khz filter - is this normal??> From: foxbat426@hotmail.com
hi sorry for the stupid queston, but i don't have a manual for my paragon II (anyday now) and i want to see if it transmits - will a corsair mic work with a paragon II? or are the pinouts different?
thanks mike, i found out that the shure 444 mic that works with my corsair also works with my paragon II - so the pinouts are the same - now i have a different problem - my audio peaks on tha paragon
my audio peaks on my paragon II with a shure 444 mic are much lower than my corsair with the same mic. for instance when i give a quick whistle into the mic in usb i'm only pushing about 80 watts out
hi, in your experience what is the best cw decoder/transmitter program for ten tecs? i'm looking for something simple to use with a computer sound card etc. as i get up to speed with my code capabili
hi ten tec gurus! hope all is well - quick questions - i forgot that my radio (Ten Tec paragon)was tuned to 17 meters and for a split second talked into the mic a full power (100 w)on 20 meters - the
hi ten tec gurus! hope all is well - quick question - i forgot that my radio (Ten Tec paragon)was tuned to 17 meters and for a split second talked into the mic at full power (100 w)on 20 meters - the
this is a follow-up question to my question regarding high swr for a split second on my paragon II - will the corsair power supply provide the foldback feature to the paragon II? i have a corsair sup
is this the proper breaker to use with the paragon and paragon II (1140). i was told ten tec no longer sells the 1140 breaker or any breaker for that matter. can someone post the equivelant airpak br
i going to use my ten tec 260 power supply with my paragon II. i do not have a manual for this unit - can someone please tell me what the output current rating is. also there are two "on" positions o
Greetings, I called ten tec this morning and the tech. there told me that an SWR as high as 10:1 for a few minutes (minutes!) would cause no problems for a paragon II. My 6:1 SWR "error" for a second
i love this radio, but i have found one negative with the paragon and that is LW reception. i sometimes like to listen to the NDB's (navigational beacons) below the broadcast band, but the paragon II
i own a paragon II and a corsair - my question is: why do ten tecs put out 100 watts at full power on the carrier vs. japanese radios putting out only 40 or 50 watts max? when i back off my ten tec's
the paragon has a tune button that you press to adjust the rf power. when this is in fully clockwise position the radio is putting out full power. according to ten tec this is full power and not a pr
yes that is what i mean - i tune my jap rigs on am where the carrier is only 40 or 50 watts. on ten tecs i guess i'm tuning on up on CW which is 100 watts. i am still a bit confused on this though -
otakebi, it has nothing to do with high SWR - i don't know where you are getting this from. when i tune my ten tec i turn up the RF power slowly and tune my swr on my antenna tuner for low swr - i do
actually you have not helped me out - you still have not answered the question - whats the difference between an am carrier and cw carrier? if it's the same as some people say why on a japanese radio