- 1. [TenTec] Orion / ACOM 2000A problem solved (score: 1)
- Author: "I2DMI" <i2dmi@contestvolta.it>
- Date: Wed, 29 Dec 2004 02:46:05 +0100
- HI, Yes it is in the ACOM. I have full instruction to do that mod. I can send via mail instructions and photos. It requests to be experienced because of high voltage into the ACOM. Today, while testi
- /archives//html/TenTec/2004-12/msg01181.html (8,930 bytes)
- 2. I: [TenTec] Orion / ACOM 2000A problem solved (score: 1)
- Author: "I2DMI" <i2dmi@contestvolta.it>
- Date: Wed, 29 Dec 2004 11:56:57 +0100
- Hi Rick, I think you mean a single band (e.g. 14Mhz only) "bandpass filter" because a wide one (1-30Mhz) doesn't solve the problem. After a full power transmission with RX+TX on VFOA a strange ARCF e
- /archives//html/TenTec/2004-12/msg01203.html (8,406 bytes)
- 3. R: [TenTec] Orion / ACOM 2000A problem solved (score: 1)
- Author: "I2DMI" <i2dmi@contestvolta.it>
- Date: Wed, 29 Dec 2004 14:36:37 +0100
- HI Barry, my answer is YES (...and the amp is tuned to that freq, you get an ARC fault if TX-VFOA and RX-VFOB) only if I move RX-VFOB on a different band; my answer is NO (...and the amp is tuned to
- /archives//html/TenTec/2004-12/msg01208.html (8,943 bytes)
- 4. [TenTec] ORION - RF output is not stable (score: 1)
- Author: "I2DMI" <i2dmi@contestvolta.it>
- Date: Sun, 2 Jan 2005 01:47:57 +0100
- Hi, when transmitting a continuous "mark" in FSK mode, the RF output power level of my new Orion is not stable. (Same in CW with a long dash) The meter shows, each 4 seconds (+/-), a short dip. (auto
- /archives//html/TenTec/2005-01/msg00026.html (7,313 bytes)
- 5. I: [TenTec] ORION - RF output is not stable (score: 1)
- Author: "I2DMI" <i2dmi@contestvolta.it>
- Date: Sun, 2 Jan 2005 17:41:33 +0100
- Hi Billy, unfortunately that happens regardless the frequency and also on a DL1000 DRAKE Dummy load. On DL it seems more variable and deeper. I'm ready for any test. Thank you. 73 Frank I2DMI -- Do y
- /archives//html/TenTec/2005-01/msg00037.html (7,074 bytes)
- 6. [TenTec] ORION - RF output is not stable (score: 1)
- Author: "I2DMI" <i2dmi@contestvolta.it>
- Date: Sun, 2 Jan 2005 21:00:39 +0100
- Martin, Bob, thank you for the messages. My idea is a little bit different. If that were an only software (s-meter) related problem, the current absorption should be constant. Sometimes the output po
- /archives//html/TenTec/2005-01/msg00046.html (10,674 bytes)
- 7. [TenTec] ORION - RF output is not stable (score: 1)
- Author: "I2DMI" <i2dmi@contestvolta.it>
- Date: Sun, 2 Jan 2005 21:39:45 +0100
- Hi Paul, I have this problem with the original TEN TEC Power Supply and also with a DAIWA 30A. My 4 el KLM (10-15-20) - 7Mhz loop - 3,5 Mhz dipole and DL-1000 (dummy load) as "ANT 1" gave same proble
- /archives//html/TenTec/2005-01/msg00049.html (9,078 bytes)
- 8. [TenTec] ORION - RF output is not stable (score: 1)
- Author: "I2DMI" <i2dmi@contestvolta.it>
- Date: Sun, 2 Jan 2005 22:51:26 +0100
- Hi Martin, (sorry for English mistakes) hi! As "Power absorption" I mean the current the ORION requires for transmission. It is abt 23amps at 13.8 Vdc for 100W output power. It is abt 14amps at 13.8
- /archives//html/TenTec/2005-01/msg00051.html (9,263 bytes)
- 9. [TenTec] ORION - RF output is not stable (score: 1)
- Author: "I2DMI" <i2dmi@contestvolta.it>
- Date: Mon, 3 Jan 2005 21:38:03 +0100
- Hi, Martin gave me a very good idea. I prepared a video showing my three S-meters: ORION - MFJ 993 - DAIWA (power supply I used for tests). You can see this video (or download the zip file) at this p
- /archives//html/TenTec/2005-01/msg00066.html (10,226 bytes)
- 10. [TenTec] ORION - RF output is not stable (score: 1)
- Author: "i2DMI - contest volta" <i2dmi@contestvolta.it>
- Date: Tue, 4 Jan 2005 10:06:55 +0100
- Hi Martin, thank you for your comments. I hope in the future this problem can be corrected. I have informed TT and I'm waiting for an answer. These variations on rf output power - this is my idea - g
- /archives//html/TenTec/2005-01/msg00085.html (9,684 bytes)
This search system is powered by
Namazu