Hi Paul, If you will reread my email, I didn't say anything about TenTec having to respond to individuals on this list. I just ask if they read this list. If I was TenTec, I would have my management
Ralph, Who would I call or visit? Do you have the names of people at TenTec that I should contact directly? I don't the people there. In the past, I have talked to Scott Robbins but since he is now M
Thank you Paul. I tend to think they probably do monitor this list. They probably just don't make that known publicly. Jerry W5JH After surviving more than forty years in some of the best and worst e
Thanks Ralph! Jerry W5JH Hi Jerry: Here is a web site w/ several numbers. The sales # or the Primary # would probably be the ones that I would use. You can also e-mail and explain your interest and t
Or buy a Elecraft K3! Jerry W5JH Oh...... No waffle maker, juicer, beer cooler or coffee spout???? Guess I'll wait for the Orion 4 or 5.... Perhaps Then, Ten Tec will have an actual real time band sc
Glenn, What is the IF of the OMNI VII and does it have an IF output? Just curious because the Elecraft P3 input is programmable from 455KHz to 21.7MHz. Also, I am thinking that N4PY has a couple of s
Andrew, I did not PUBLISH the widespread complaint. If you will look closely, I sent a private email to Glenn. Glenn then decided to make the email public without asking me. My email was meant for Gl
Andrew, Glenn thinks Paul was just having a bad day (as we all do from time to time). And, I am sure Paul was just stating company policy. Glenn is pretty good friends with Paul and I am hoping he ca
Folks, I am down to only a few boards, PICs, and Parts kits left. I have 10 PCB boards, 7 sets of programmed PICs, and 7 parts kits. When these are gone, that is it. I do not plan to buy anymore. If
Michael, your parts will go out tomorrow. Look for them by the weekend. Jerry W5JH --Original Message-- From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com] On Behalf Of Michael
Glenn, I guess it would depend on how many people were interested. To keep board prices down, you need to sell 50 or so PCBs. The board would be small - maybe 1.5 inch x 1.5 inch and the cost of the
Glenn, The Display Logic Board was Steve Hunt's project and he is the one who deserves all the credit. I was just a middleman. Assuming a person could sell 50, the cost of a small 2 sided PTH PCB wit
Yes. Does the Corsair II have an internal keyer? _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Folks, I am trying to remove the main tuning knob from the Corsair II. Someone told me the set screw took a 1/16 inch hex wrench (AKA allen). However, I have been unable to get the 1/16 inch Allen wr
Thanks to Dub Thornton and Andrew Moore, I was able to finally remove the tuning knob from my Corsair II without resorting to using bad words! I was trying to use a 1/16 inch hex wrench but Dub and A
I think I'll pass on the exclusive club! Does the dial skirt just slip/slide off? Jerry W5JH Jerry, "Am I now in the exclusive club? ;-) " Not until you've drilled out the set-screw hole and re-tappe
Glenn, I am going to try my best to skip that club. ;-) Jerry W5JH I think to be a member of the Ten Tec Totally Twisted Club, you have to rebuild the PTO and drop the little locking pin into the car
Folks, I have one bare Display Logic PCB left. Everything else has been sold. If you would like to purchase this last PCB, it is $17 which includes shipping. Hopefully, we can all keep our Corsairs r
Scott, I think Glenn WA4AOS might have one or two he could sell you. He does repairs for Corsair II's and bought several to have in stock. Jerry W5JH Folks, 2nd time around with this msg...I realize
Steve, I have a TenTec model 234 speech processor I use with my Corsair II. It works well. As I understand, the 715 is an upgrade of the model 234 using more up-to-date parts. The model 234 has some