Scott, I think Glenn WA4AOS might have one or two he could sell you. He does repairs for Corsair II's and bought several to have in stock. Jerry W5JH Folks, 2nd time around with this msg...I realize
Steve, I have a TenTec model 234 speech processor I use with my Corsair II. It works well. As I understand, the 715 is an upgrade of the model 234 using more up-to-date parts. The model 234 has some
Folks, I am down to only a few boards, PICs, and Parts kits left. I have 10 PCB boards, 7 sets of programmed PICs, and 7 parts kits. When these are gone, that is it. I do not plan to buy anymore. If
Michael, your parts will go out tomorrow. Look for them by the weekend. Jerry W5JH --Original Message-- From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com] On Behalf Of Michael
Glenn, I guess it would depend on how many people were interested. To keep board prices down, you need to sell 50 or so PCBs. The board would be small - maybe 1.5 inch x 1.5 inch and the cost of the
Glenn, The Display Logic Board was Steve Hunt's project and he is the one who deserves all the credit. I was just a middleman. Assuming a person could sell 50, the cost of a small 2 sided PTH PCB wit
Folks, I am trying to remove the main tuning knob from the Corsair II. Someone told me the set screw took a 1/16 inch hex wrench (AKA allen). However, I have been unable to get the 1/16 inch Allen wr
Thanks to Dub Thornton and Andrew Moore, I was able to finally remove the tuning knob from my Corsair II without resorting to using bad words! I was trying to use a 1/16 inch hex wrench but Dub and A
I think I'll pass on the exclusive club! Does the dial skirt just slip/slide off? Jerry W5JH Jerry, "Am I now in the exclusive club? ;-) " Not until you've drilled out the set-screw hole and re-tappe
Glenn, I am going to try my best to skip that club. ;-) Jerry W5JH I think to be a member of the Ten Tec Totally Twisted Club, you have to rebuild the PTO and drop the little locking pin into the car
Folks, I have one bare Display Logic PCB left. Everything else has been sold. If you would like to purchase this last PCB, it is $17 which includes shipping. Hopefully, we can all keep our Corsairs r
Folks, The Group buy of Steve Hunt's Corsair II Logic Board is NOT going well. Many people indicated they wanted one but have failed to pay the $17 for the bare board. To me, $17 is really cheap insu
I had mentioned in a previous email that could buy and distribute the programmed PICs. The cost of the PIC from Mouser is about $5 each. I was going to charge a few $ to do the programming and shippi
The easiest way to pay is via paypal. Goto paypal and click on send money and enter my email address as shown above. Put in $17 for 1 board or $33 for 2 boards. Under instructions, tell me who you ar
Folks, I have good news. With the promised checks in the mail, we now have enough participants to make the group buy. I will make the buy on Tuesday since for some reason everybody wants Monday off.
Andrew, You don't need a scope but you will need a frequency counter. You can determine the drift is coming from the PTO by hooking a frequency counter up to the output of the PTO and monitoring the
Folks, Some people have inquired if I could supply a complete kit of parts for the Corsair Logic board. I have figured out the cost of a complete kit. For the PCB, Programmed PICs, and rest of the pa
My paypal address is the same one as above. Jerry W5JH Hi I wil, buy a kit .what is your paypall address ,ken ko5y . for board, $25 _______________________________________________ TenTec mailing list
Curt, The Corsair II only uses the microcontroller to display the frequency and to do the keying. It really does not control anything. The Corsair II still uses the "old" PTO, crystal filters, audio