Good deal. Glad you found the problem. -- Original Message -- From: "Don Rasmussen" <wb8yqj@yahoo.com> To: <tentec@contesting.com> Sent: Friday, March 30, 2012 2:34 PM Subject: [TenTec] OMNI VI+ foun
I am sort of interessted in purchasing and Eagle, but there's the IMD issue. Please tell me it ain't so, especially if there is someone out there who still thinks it is so and is therefore willing to
I travel to our farm several times a year, and while I am there, I cannot operate. I guess I could take one of the rigs I have here, but I am reluctant to leave a rig in the house because it has been
Gentlemen, Thanks so much for all those ideas. I would love the Eagle I am sure. On the other end of the spectrum, the Century 21 is a good one. In the middle, the K2 would be nice. I will be ponderi
I had remote capability until I sold my OMNI VI+, but I do not have an internet connection at the farm. Good idea, but not an option for the farm. Thanks. -- Original Message -- From: "WA0BAG" <bagma
Thanks Kris. I will take a look at the 857D. -- Original Message -- From: "Kris Merschrod" <Kris@merschrod.net> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com> Sent: Thursday, February
I breathed a sigh of relief for you Scott. Good job. Joe -- Original Message -- From: <scottsheppard@videotron.ca> To: <tentec@contesting.com> Sent: Saturday, February 18, 2012 10:13 AM Subject: [Ten
Excellent observation. -- Original Message -- From: "Mike Bryce" <prosolar@sssnet.com> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com> Sent: Saturday, February 18, 2012 10:42 AM Subject
Check the E voltage at the PTO. If this voltage is not about 8 volts, the PTO is disabled. The E voltage is jumpered at the ACCESSORY jack on the rear panel. If it is not jumpered, the PTO will not h
Joe -- Original Message -- From: "Michael Silevitch" <msilevitch@coe.neu.edu> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com> Cc: "Michael Silevitch" <msilevitch@coe.neu.edu> Sent: Mond
Well Mike, I guess the next thing to do is to see if there is anything coming out of the PTO. You could use one of the scopes that everyone has been talking about or an RF probe. It is looking like t
Did you see the post by Gary, AB9M. I still think there is an accessory jack and that a jumper is required. -- Original Message -- From: "Michael Silevitch" <msilevitch@coe.neu.edu> To: "Discussion o
Mike, Are you sure there is no ACCESSORIES jack on the rear panel. It is a 9-pin Molex connector. If it is not there, then you are right, there will be no jumper. The manual for the OMNI A clearly ha
Having built a VFO which does everything that the 243 does and more, I can tell you how that unit works with the Corsair II and other transceivers which have the ENABLE pin on the PTO. The OMNI obvio
That should tell you if it is the PTO, and you can proceed from there. I will be listening and looking. -- Original Message -- From: "Michael B. Silevitch" <msilevitch@coe.neu.edu> To: "'Discussion o
Mike, I do not know what the PTO looks like in the OMNI. In my Corsair II, all connections are solder. The output goes to a feedthrough. The feedthrough solders to a piece of RG-174 coax which goes d
Well Mike, you are not getting a PTO signal. Have you verified that you have continuity from the PTO to the PTO OUT jack? Once you get continuity and there is still not signal, you can go to work tro