Mail Archive Search: <+from:k5xs@aol.com>

Results:

References: [ +from:k5xs@aol.com: 186 ]

Total 186 documents matching your query.

1. Re: [TenTec] Omni V backup battery (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Thu, 16 Jun 2022 16:10:57 +0000 (UTC); Wolfgang, Looking at the Omni V schematic, the battery feeds two chips on the Logic board: U7 (which appears to be the main microprocessor) and U11, which converts TTL to RS232. I wonder if you have; /archives//html/TenTec/2022-06/msg00013.html (8,519 bytes)
2. [TenTec] Orion 2 Receive Audio (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Sun, 20 Mar 2022 00:20:16 +0000 (UTC); I have an Orion 2 that transmits great, but the receive audio bandpass sounds very narrow. I've verified the filters are behaving, and the receive width control is set right. Any clues? TIA, Bernie K; /archives//html/TenTec/2022-03/msg00011.html (7,359 bytes)
3. Re: [TenTec] Orion 2 Receive Audio (score: 1): Author: BERNARD SKOCH <k5xs@aol.com>; Date: Sun, 20 Mar 2022 13:50:02 -0500; Using latest firmware, and already tried full reset. Thanks; /archives//html/TenTec/2022-03/msg00014.html (12,434 bytes)
4. Re: [TenTec] Orion 2 Receive Audio (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Sun, 20 Mar 2022 21:43:13 +0000 (UTC); Another clue: The S-meter is consistently high, even though I just ran through the published S-meter calibration procedure (and it calibrated perfectly). The S-meter rests at about S-8 and deflects u; /archives//html/TenTec/2022-03/msg00015.html (13,670 bytes)
5. Re: [TenTec] Ten Tec Orion II problem -- will not power on (score: 1): Author: BERNARD SKOCH <k5xs@aol.com>; Date: Mon, 14 Feb 2022 14:36:39 -0600; I would try another power supply and check the A9 board (it may have failed after you rebuilt it). I would also check the integrity of the power connector.; /archives//html/TenTec/2022-02/msg00029.html (9,491 bytes)
6. Re: [TenTec] Orion tuning dial drag (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Tue, 12 Oct 2021 01:28:55 +0000 (UTC); Mike, The ring may have gotten lightly fused to the back of the knob. I recommend you remove the knob and get a look at the copper tongues (with felt pads) and see if they have seized to the knob bac; /archives//html/TenTec/2021-10/msg00007.html (8,126 bytes)
7. [TenTec] Orion II For Sale (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Mon, 25 Oct 2021 21:45:28 +0000 (UTC); Orion 566AT for sale. All filters installed. Works great. No issues. No manual. No power cord. No mic. $900 plus exact costs for professional packing and shipping. Money back (less shipping both ways; /archives//html/TenTec/2021-10/msg00011.html (7,492 bytes)
8. Re: [TenTec] Right Channel dead on Orion 2 phones (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Thu, 23 Sep 2021 22:11:41 +0000 (UTC); Kim, I've had it happen when I have used a mediocre adapter to take my 1/8" phones plug and adapt it to the 1/4" jack. Have you reversed the sources to see if the problem follows the source or the ja; /archives//html/TenTec/2021-09/msg00027.html (9,215 bytes)
9. Re: [TenTec] Right Channel dead on Orion 2 phones (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Fri, 24 Sep 2021 16:46:00 +0000 (UTC); Glad to hear it, Kim! Gremlins. 73,Bernie Well, it must've been a bad junction between my ears because everything seems quite normal, now. I dunno what I did to cause it or fix it. Oh, well! Kim N5OP; /archives//html/TenTec/2021-09/msg00031.html (10,866 bytes)
10. Re: [TenTec] filter (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Sun, 2 May 2021 19:39:40 +0000 (UTC); Rodney, This article discusses some source filtering at the end: Microsoft Word - Document14 (arrl.org) Good luck! Bernie Does someone know if there is a filter to filter out electric fence interfere; /archives//html/TenTec/2021-05/msg00003.html (7,915 bytes)
11. [TenTec] Orion II Keypad Source?? (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Thu, 13 May 2021 16:37:17 +0000 (UTC); Had a "feline incident" whereby one of our dear cats plucked out the NOTCH button on the membrane keypad beneath the display of my O2, and it's nowhere to be found. (I know, hilarious!) Sent an email; /archives//html/TenTec/2021-05/msg00038.html (7,264 bytes)
12. Re: [TenTec] Ten Tec Argo V repair (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Tue, 26 Jan 2021 20:08:11 +0000 (UTC); I recently had an Orion II in to Ten-Tec for repair on a problem that was just beyond me to fix. Service was good, reasonably priced, but slow. The tech called me to get payment information and to; /archives//html/TenTec/2021-01/msg00045.html (10,210 bytes)
13. Re: [TenTec] Start up issue with Orion 2 (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Mon, 8 Jun 2020 02:17:47 +0000 (UTC); Barry, I think your diagnosis is correct based on what you posted. It's consistent with the symptoms I experienced (and remedied with the A9 board fix). (I assume you have verified that the rig is c; /archives//html/TenTec/2020-06/msg00020.html (8,919 bytes)
14. Re: [TenTec] Century 22 (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Sun, 21 Jun 2020 15:34:07 +0000 (UTC); Fond memories of my Moseley CM-1 receiver. Any novice that worked WAS using a Heathkit HR-10 should be nominated for saint hood. Novice band with that radio? You were lucky if you knew you were some; /archives//html/TenTec/2020-06/msg00098.html (9,822 bytes)
15. Re: [TenTec] Orion (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Thu, 2 Apr 2020 18:24:41 +0000 (UTC); Are you sure the problem isn't in the mic itself? Seems odd that it would follow to the rear PTT jack as well. I would take the time and clean connectors. Do them one at a time. Be careful and assu; /archives//html/TenTec/2020-04/msg00002.html (8,968 bytes)
16. [TenTec] O-II Encoder Part? (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Wed, 22 Apr 2020 20:31:46 +0000 (UTC); I have decided it's time to replace the digital encoders on my Orion II. I found an article on-line describing replacing the Orion I encoders, with a reference to this part: https://www.digikey.com/p; /archives//html/TenTec/2020-04/msg00008.html (8,036 bytes)
17. Re: [TenTec] O-II Encoder Part? (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Sun, 26 Apr 2020 23:44:07 +0000 (UTC); Thanks to all for the many helpful replies. 73,Bernie I have decided it's time to replace the digital encoders on my Orion II. I found an article on-line describing replacing the Orion I encoders, wi; /archives//html/TenTec/2020-04/msg00027.html (8,289 bytes)
18. Re: [TenTec] FS: Orion-II 566AT & 6-filters (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Wed, 11 Mar 2020 13:42:06 +0000 (UTC); Bill, I'll take it. How would you like payment? Bernie I have for sale an Orion-II 566AT in excellent electrical and cosmetic condition. SN#10C11005 with version 3.033xd firmware. All six filters (6; /archives//html/TenTec/2020-03/msg00014.html (8,253 bytes)
19. [TenTec] 708 Mic Switch (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Sun, 22 Mar 2020 14:46:04 +0000 (UTC); The PTT switch on my 708 mic is getting mechanically flaky. Does anyone know a source for a replacement switch? And does anyone have any hints about removing and replacing the decorative plate on; /archives//html/TenTec/2020-03/msg00021.html (8,067 bytes)
20. [TenTec] Ten Tec 708 Mic Switch Fix (score: 1): Author: Bernie Skoch <k5xs@aol.com>; Date: Mon, 30 Mar 2020 23:25:29 +0000 (UTC); I asked here a couple of weeks ago if anyone had a source for a replacement PTT switch for the Ten Tec 708 mic. After about 15 years the switch started getting really flakey, sticking in the "on" po; /archives//html/TenTec/2020-03/msg00045.html (8,022 bytes)

Current List: 1 - 20
Page: [1] [2] [3] [4] [5] [6] [7] [8] [9] [10]