In a reconfiguring of my TT gear, I have come up with an extra filter. It is TT 219, the 250 Hz filter for the main IF (9.0 MHz). $65 shipped or trade towards the narrow INRAD roofing filter kit. Ple
I now have a pair of OmniVIs and would like to use them in a sort of poor-man's SO2R. Actually I believe what I want to do is called SO2V but will actually be with two radios. What I would like to do
Yet another question. The Alpha 87A amp does not have a QSK keying loop as do the TT amps. Is there a best way to key it from an OmniVI? Has anyone done this? I am thinking that the TX REQ signal fro
The 219 narrow (250) filter for the main IF I posted earlier F/S is now sold. -- 73 Allan K7GT _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.c
Has anyone tried or considered this? Using the 1.8 kHz filter (TT 218) in place of the 2.4 kHz main filter in the first IF? CW only... This would allow three choices of bandwidths instead of two. (18
I now have an OmniVI+ in the queue at TT service.( I waited until after the holiday season shipping madness had subsided to send it in.) Unfortunately the estimated time before their OmniVI tech gets
Is there a band decoder available that can use the Tentec OmniVI serial data info to provide full band info? In particular, I wish to have WARC band info separated from the 'contest' band info by thi
I would be happy as punch to pick up another Herc II. I don't need the power supply (plan to use a 70A Astron with a big battery). I do need the interface cable to an OmniVI. The amp doesn't need to
I have an unused/uninstalled INRAD roofing filter kit for the OmniV, OmniVI, OmniVI+ radios. It has the 2400 Hz B/W filter (INRAD #764). I would like $120 shipped. INRADs price is $175. Check/MO OK.
I have a CW filter for the Omni VI and V radios F/S. It is the INRAD # 766. INRAD price is $125. I will sell/ship for $85. CONUS only, check/MO OK. No PayPal. -- 73 and best wishes for the Holidays
I am cleaning out the shack during winter break... I found the two Airpax breakers formerly installed in a power distribution panel. That panel has been stripped out and no longer being used. The two
The two Airpax breakers now have a new home pending. Thanks for your queries. Allan K7GT _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contest
I need an encoder for the OmniVI series. I think it is the 302 (not in the shack right now). Must be smooth and free. -- 73 Allan K7GT _______________________________________________ TenTec ma
My TT station has been stacked in a corner for a while. I just put it together yesterday before the DX test. The Herc II came up without all four sectors of the power supply cable/connector mated. I
I would like to purchase a 301 remote encoder for my OmniVI. -- 73 Allan K7GT _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.
I am still looking for a 301 remote tuning encoder pod. If you have one you can spare, please contact me. -- 73 Allan K7GT _______________________________________________ TenTec mailing list T
My OmniVI/opt3 has a receive problem. It will intermittently drop down in received signal level by 5 or 6 S-units. This dropout stays for long periods of time yet is intermittent for sure. There are
The main optical encoder on one of my OmniVIs is quite stiff. I am wondering if there is some way to lubricate it. It turns, but not nearly as freely as one might wish for. Yes, I loosened the knob c
I recently purchased an OmniVI+ and if I received a manual with it, I cannot find it! I have sold (actually traded) that rig away and need to find an original manual to get to the new owner. If there
Hi, I finally picked up a 2nd 50A Astron power supply to make a pair. Are there any issues in paralleling these to run the Herc II? I am going to verify that the terminal voltage is identical within