Reflector folks: We are working on a late model Corsair II that I purchased last fall but never had occasion to turn on until May. It didn't work, had other things to do... Anyway, we have figured ou
I have found I need a set of filters for the bandpass section of a Corsair II. Highest priority is the 500 Hz, 1800Hz is next, and 250 Hz if it comes along. Tentec or INRAD, either is fine. Any out t
The trouble mentioned yesterday with the Corsair II have been located and fixed. It turned out to be a broken wire from a segment of the dual drive pot--the segment that goes to the CW side of the ba
Anyone have an unused 500 Hz filter for the 6.3 IF on OmniV, VI, Corsair II? I could use a 250 as well but not as important. -- 73 Allan K7GT _______________________________________________ TenTec ma
I have located and purchased the two 6.3 MHz filters for my Corsair II. Tnx all! -- 73 Allan K7GT _______________________________________________ TenTec mailing list TenTec@contesting.com http://list
I am toying with the wide filter trial on both an OmniVI/opt3 and a Corsair II. Does anyone have an unused pair at reasonable price or, even better, a pair to loan me for a month's trial? I was so ta
At one time, I had the interface cable for my OmniVIs. It apparently is lost in a shack reorg. Going back to my old manual, I have comments to the effect that the schematic/sketch is in error and tha
I am clearing out the shack. The first obvious item that is no longer needed is the Tentec # 1125 fast-acting breaker designed for the Argosy series. 9A working, 12.5A trip. This breaker is N-I-B alt
I have been watching the prices of OmniVIs drop dramatically so that it likely wouldn 't pay to sell them off. Also, since the Orion II is no longer in production with no likely follow-on top-end xcv
I recently picked up a Tentec 6N2 at a reasonable price. I know the 20w will be suitable for local work, but want an amplifier for some contest play. Some of the available 2m amps out there have a co
Tentec fans! I happened across a clean Orion II F/S over the weekend. Just got the word that I am the apparent purchaser. So,... I have to sell some of the following Tentec gear! I have the following
Gang, Having just acquired an Orion II, I need some or all of the following: 8-pin Tentec desk microphone (706??) optional roofing filters, either TT or INRAD: 1800 Hz 600 Hz 300 Hz (maybe) matching
I am selling my OmniVI collection to resupply my radio money fund. I have two fully loaded OmniVI/opt3s. All filters, cooling fan. fully functional. Also have two power supply/speaker units (a 961 an
I have located one roofing filter and a remote tuning pod for the newly-acquired Orion II. I still need the following: Tentec 2001 roofing filter (600 Hz BW) Tentec 708A desk microphone (8-pin) Thank
Still selling goodies to fund the recent Orion II purchase. I have two OmniVI/opt3 s F/S. All the filters, could come with microphone and speaker/p.s. try $800 for the VI, additional for accessories
With all this talk about how bad the Orion II is, I am wondering if someone is willing to part out one and sell me the RX-366 that is troubling them. All fun aside, I would really like to locate a RX
I am putting my TT 526 for sale to fund a 100W 2m all-mode that has just become available (IC275H). For those who are not familiar with it, it is an all-mode 20W radio covering both 6 and 2m. They ar
Subject line tells the tale. The 6N2 sold quickly. -- 73 Allan K7GT _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listi
I recently acquired both an Orion II and a RX-366 subrx board(s). The RX-366 was successfully installed yesterday and the original board is now into my inventory of 'stuff'. If someone out there need
I am checking out a Scout that has been sitting around the shack of a local OT ham with the idea of perhaps purchasing it. I have not yet put it to a real antenna but did some checking with a good du