Rick, I think it must be the monitor circuit in the rig itself as Barry pointed out.We are using exactly the same rig, and headset, and mine works fine. The slight hum I have occurs when either a) li
Maybe 200 watt input, but more or less a 100 watt output rig. Mike, K9MI does anyone know for sure the power output of the tentec delta (580)? on one actual advertisement it lists the delta as a 200
Just to see if it works at all, any mic should do. Maybe even the Electro Voice is wired up wrong or has a wire broken off? Should at least be able to find out if it's the rig or mic. Mike, K9MI it s
John, pin 1 should be mic audio pin 2 Grnd pin 3 PTT Pin 4 +4 volts dc What I have is an Omni V, but I think all 4 pin Ten Tec connections are the same. 73 Mike K9MI hi sorry for the stupid queston,
"Life's been good to me so far....." Well...it was new in the box... and the buyer is Joe Walsh. Royalties sure are a good thing! _______________________________________________ TenTec mailing list T
Unlikely. Do you have a Ten Tec PS? If not, I'd get one. When the rig draws too much current, it just shuts everything off. I think there are circuit breakers for "non TT" power supplies also. But it
Yes, if it draws too much current, it will just shut everything off. Turn the rig and ps power switches off, say thank you to the Ten Tec gods, turn it all back on, use the right antenna! 73 Mike K9M
John, what Japanese rig only puts out 40 or 50 watts keydown? Or do you mean it only puts out that much when you are "auto tuning" it? Mike, K9MI i own a paragon II and a corsair - my question is: wh
Ok, John thanks, that clears things up for most of us. Dan: I have had an Icom 746 that would drop to 50 watts out at a 1.5:1 swr. Not a terrible rig otherwise, but that is BAD IMO! Rig now is an Omn
I had a suggestion to at least slow that problem down a little bit, but it didn't really catch on. Put your email in a signature file, or if you are selling, put your email address near the bottom of
Ralph, Carl, N4PY makes a new chip for the Omni V called V.92 which does not require any mods to the radio (outside of changing one chip). I really don't use memories that much for hf use, but you ca
"Looking forward to the Orion III, which hopefully will also have 6, 2, and 440, making it the only radio one would EVER need (after all, why should my little cheap IC706 Mk2G have this and not my Or
This is a joke, right? Mike "Looking forward to the Orion III, which hopefully will also have 6, 2, and 440, making it the only radio one would EVER need (after all, why should my little cheap IC706
Paul, I hit "send" too fast. My real reply should be in the achieve. I'm definitely against a Ten Tec "do it all" radio (vhf, uhf, 220, 1.2 gig). Someone was complaining that there 706 did it all and
Correct me if I'm wrong, but I've always thought of the V.9 and V.92 as firmware, not software. And it sounds like the display problem is hardware. 73, Mike K9MI Bob McGraw - K4TAX writes... Could th
I was thinking maybe I could work on him as a fellow SMC member and get a discount. A few things left in my shack cleanup - Nearly mint 961 power supply. $100 plus shipping. KR1B iambic paddles (matc
Yes it does. I was surprised that Mike bought a 7800. I've read about failures with some of them. I'm pissed if my 850 dollar radio quits. I'd probably really lose it if something like that happened!
Ditto here Walt, and I never turn down at least a lower speed Pentium (100 mhz and up) if anyone offers. I did buy a Toshiba notebook with Vista, but it's use it's primary use will be internet/multim
I just sold an Icom 746 due to all the birdies and bought an Omni V. It has a few, but nothing like the 746. 73, Mike K9MI Don, Every radio I own has birdies, including the Icoms, Yaesus; and yes, my
Yes it is Rick. But if you put n4py.com in today, it changes to the address. At least from here. Mike, K9MI Actually it is simply www.n4py.com http://www.ralabs.com/n4py/ This works for me. 73 Martin