Mike, So you are using audio compression AND OII SP? Why do you need audio compression with SP? MAyb I should get a TT 31 or the one you have? PLease share the details of your setup: Mic, your using
Wayne, Yes, I do understand about the revenue issue...I also understand that these days with Internet...word travels fast and any bad news hurts SALES! I anyone here does not believe that this firmwa
I have my low freq. rolloff at 100...why would I want to have any audio below that? I use TX BW of 2850..why would I waist band space using anythin wider? Everyone that knows my voicesays with thosw
Or...better yet..just give Jack Burchfield a call. He's a great guy to talk to. 73, Lee I have an idea. How about anyone that is unhappy with TenTec send a email directly to them? Jeff ______________
Joe, Go back to the USB serial converter. BUT go to the hardware manager in windows and disable that multiport serial card first. Sounds like conflicts to me...also, do you have the latest windows SP
Mike, Very complete and very informative answer..Thanks. I am excited as to the fact that I think I am underdriving the radio. I will follow your suggestions. 73, Lee, KC9CDT Hello Lee: Please see my
John, Interesting...you have not had the red flash screen when using the standard sweep display? Or have you only used the waterfall? 73, Lee I am of the opinion that the new firmware is a very nice
Jerry, Yes indeed...and I use it today..stilll get reports like ' WOW that audio is realy nice' Same on my Drake T4X-C 73, Lee that? like in person. want one anyways...I'll stick wih OII. The vintage
Ron, Good info to pass along to TT, 73, Lee I have seen it several times on the standard sweep display and it seems to coincide with very strong signals that get past the HP/LP RF filters in the fron
Haven't you been reading the posts? This takes 5 minutes...there is definetly a problem on your PC setup. Lots of possible problems have been posted. Sounds like issues with your serial port/configur
Yes, Any async serial device is picky about the baud rate, data bits, parity and stop bits...they have to MATCH each other. It will not work otherwise. 73, Lee Having the wrong COM port selected woul
Tom, Easy answers. 1) The width is no longer changeable ( I think it is 36 Khz now, but you can tell by taking note of the current freq. then tune to the end of the sweep with the tuning cursor, how
Jim, This is what we have been talking about all along...nothing new. Just about everyone has seen it. 73, Lee The radio had been running on Rx for a few hours, 20 and 80 meters. The 80m band was dea
Once mine goes red...I have to turn sweep off/on to get it going right again...That's not a feature. 73, Lee Didn't someone point out that a type of sound card software uses a red screen to indicate
One thing I found out this week on a QSO...The OII SP set on 7? vs off...the ham on the other end didn't see much difference. So, I hope the 715 might work better. (yes running the latest firmware) 7
Greg, Thanks...makes sense. 73, Lee In the past (25 years ago), when I was running a Ten Tec RF processor with my Ten Tec 544, if the signals are strong, the other guy couldn't tell much difference e
Bill, I would call Ten-Tec and ask those questions... Did you read the documentaion that came with the upgrade? It is in C:\program file\ten-tec folder That's all there is..just call them. The doc is
610,? BC-610??? I was on the TT site today....no such thing? What the heck is this you speak about? 73, Lee Maybe it's a BC-610. Jim Subject: Re: [TenTec] 610 Has started shipping today What is the 6
I've used a BC610 myself!! 73, Lee Lee Simmonds Summit DCS 574-878-4123 Office 260-403-6936 Cell --Original Message-- From: Wes Attaway (N5WA) <wesattaway@bellsouth.net> To: 'Discussion of Ten-Tec Eq
Is the 610 on the TT site? Where? Thanks, 73, Lee --Original Message-- From: Don <w4to@tds.net> To: Discussion of Ten-Tec Equipment <tentec@contesting.com> Sent: Fri, Aug 28, 2009 5:36 pm Subject: Re