I am observing a troubling malady with my Jupiter. from time to time with no pattern I can recognize it will stick in transmit and the only way I can get it out of transmit is to power the rig off an
More info: I haven't tried connecting a PC at all yet. Just tried a master reset, no effect. The OS Version is 1.26 b7 11.11.2003 It seems to happen on a longer transmit even into a dummy load. TX 90
I took your advice and downloaded the file. Had to set up a network between my Linux box and the older Windows box needed to run the exe file and transfer it over there. (Nothing but Linux in the rad
In the process of momentarily relocating my Jupiter to another room with a Windows PC (to load the updated OS) I think I may have applied reverse voltage to the power connector ... Arghhh! I was usin
My schedule (12+ hours days through Wed.) will keep me from cracking the box to do a sight and smell assessment of the potential damage. I sure appreciate the helpful hints from so many and will repo
I am looking for up to 6 555's for a missionary friend of mine in Honduras. Does anyone have a good unit for sale or donation? Dennis As long as some missionary nets in Africa and South America use t
Finally have a little time to troubleshoot. No clicking relay, just no response at all. There is no visible damage to anything that I can see on the little circuit board to which the power connector
I have lifted the damaged zener, no effect. I am going to replace the transistor with a 2N2222 per the recommendation of Tentec. Will advise later in the week when I again have a few minutes to work
Question, please? Why use an external tuner vs the internal model that closely matches the Jupiter? Is there any loss in performance external vs internal? doc 73 Kurt -- Original Message -- From: "Bo
Do we know why LDG is discontinuing the AT-11MP? Any reasonable concerns re. long-term reliability and parts availability for repair? Does the AT11-MP do a reasonable job of filling the gaps between
Does this apply to all models or one in particular, please? If one in particular it would help, especially for someone browsing the archives down the road, to have the model number in the Subject and
NOTE: I think this discussion should be moved to the more appropriate rfi@contesting.com list and now invite folks to follow it there. Since the political hacks on the 911 Commission have opened the
Will this OS work on Jupiters or should the Subject include the identifying word "Orion"? doc Alan N5NA -- Thanks! & 73, doc kd4e West Central Florida Drake, Heathkit, Kenwood, TenTec, Yaesu Radio Li
Sounds like it could be rf feedback. I have been fighting this symptom since I got the rig. good luck. bill w6eet Have you definitively traced the weakness in managing rf feedback problems to the Jup
Hope to have my used Jupiter in a couple of weeks and would like to know what the recommendations are for desk mics. I have a well-worn Heil headset, wired for a Kenwood, for which I could wire an co
Jason Buchanan wrote: edoc wrote: Is the TenTec Model 706 important for the Jupiter to shine or would most any mic sound OK? The 706 is perfect match - crisp and clean audio. 73 Jason N1SU The initia
I would agree. Just remember, typically a larger antenna will out-perform a smaller antenna. Thus a full wave loop, having more wire in the air, should out-perform a 1/2 wave dipole. 73 Bob, K4TAX I
Larry Greenberg N5BEA wrote: Through my commercial contacts, I have established that the price point will compare favorably with the Orion. However as an innovative marketing approach, Icom is offeri
Bill, AK5K Anyone have the wiring differences between a mic wired for a Kenwood (e.g. 430s, 450s, 690s) and the Jupiter handy, please? Thought I'd get my old Heil headset wired ahead of time. Actuall
Richard Hemingway wrote: I don't know if this is what you want. TT mic wiring is: pin-1 MIC pin-2 GND pin-3 PTT pin-4 +9VDC I think that it is the same as on the Orion and Omni's. Dick, N5XRD That wi