I would like the fan kit Ken. How should I pay you? Tnx, Mike Cumbo, ND4S Sent from Mail for Windows TenTec Orion Transceiver, Filter, Microphone, Fan, and more For Sale: . TenTec Orion 565 HF Transc
The Omni 7 manual says 14 ga minimum, 12 ga recommended. I expect it is the same for the Orion 2. Mike Cumbo, ND4S Sent from Mail for Windows Does anyone know the gauge of the power cable for the ORI
Ken, the Collins mechanical filters are used only in the Omni 7, not in any of the other rigs. None of the filters for the Eagle or Argo 6 work in any other rigs except maybe the Orions, I have no ex
Is that to an antenna? What SWR? Have you tried loading a dummy load? Mike Cumbo, ND4S Sent from Mail for Windows Hello All, I have a Centurion amplifier that appears to have a problem delivering the
Hello Wolfgang, Great amp, love mine. Does the problem exist on all bands or just on one band? 73, Mike Cumbo, ND4S Sent from Mail for Windows Hello: I have a problem with my hercules II. When switch
Good news Jim. If I remember correctly, Ten Tec shipped the Centurion with the power transformer and tubes separate and the purchaser had to install both. That pinched wire was probably done by the o
Hello again Jim, My aging memory failed me. A look in my Centurion manual shows the tubes were shipped separately but it says nothing about the transformer being shipped separately or having to be in
Hello Jim, Be very careful with the high voltage in that amp! Make sure your probe is suited to the high voltage. I would check at the K contact on the parasitic suppressor board just near the plate
Hello Joe, Have you gone back to your original test on the dummy load when you observed 20 watts output? See if that still works. Mike Cumbo, ND4S Sent from Mail for Windows Hi all, So I just bought
Glad you found the problem. The Argo V is a great little rig, I am on my second one, just wish it had an RF Gain control rather than the squelch! 73, ND4S Sent from Mail for Windows Hello Mike, I did
Looking at the manual, there is a relay in the circuit near the antenna connector, looks like that is the T/R relay. There is a bunch of relays on the output filter board. Lots of places for Deoxit!
Seems like I remember Mike Brice at The Heathkit Shop made a clone of the Ten Tec CW filter for the Argosy. You might check with him and see if my memory is correct and if it is still available. 73,
I will buy the Herc PS to O6 power cable. Tell me how you want to do it. Tnx, Mike Cumbo, ND4S Greetings everyone, Time for a bit of shack thinning. FS: TenTec OMNI-VI OPT-3 SN #02A10486 - In excelle
I bought the 6+ I am now using for $400 including power supply, filters & manual. It was an estate item at a hamfest a year or more ago and is very clean. I think that is a bottom dollar price for yo
Should have read closer, you have the roofing filter. Have you noticed a decrease in ringing using the narrow IF filters? Mike Cumbo, ND4S It would seem like I am advertising my OMNI6+ on this list b
A buddy has a Ten Tec Titan II amp that needs some work. Is there anyone who works on Ten Tec gear within a few hours drive of the Greensboro/Winston-Salem, NC area? I think shipping would distroy th
Thanks for the info, I will check him out. Got a spare tube, probably the only guy around with that in his hip pocket! I wouldn't be lucky enough for you to have any contact info on Vlad would I? Mik
Thanks Wayne, Mike has had this amp since last August. His tech guy had a heart attack last summer and the backlog is apparently quite long. Mike Cumbo, ND4S Try Mike Atkins at Triad Electronic Suppl
Thanks Paul, Florida is too far to drive to deliver/pick up the amp and I don't think it would ship well. Way too heavy and don't want to have to take the xfmr out. Tnx, Mike Cumbo, ND4S -- Original