Gerd, the remote encoder has been sold. tnx - Bill I meant the 301 remote encoder for Omni VI.. electrical and cosmetic condition. TCXO installed. INRAD 600Hz roofing filter with PROC switch mod. Ful
Greetings everyone, Time for a bit of shack thinning. FS: TenTec OMNI-VI OPT-3 SN #02A10486 - In excellent electrical and cosmetic condition. TCXO installed. INRAD 600Hz roofing filter with PROC swit
Markus, In addition to the SNAPHAT battery on the logic board, there is a coin-battery on the antenna tuner board. This battery stores the memories for the tuner, and should be renewed as well. 73 Bi
I have for sale an Orion-II 566AT in excellent electrical and cosmetic condition. SN#10C11005 with version 3.033xd firmware. All six filters (6K,2.4K,1.8K,1K,600,300) included on the IF board. Includ
TenTec 288 1.8kHz 6.3mHz IF 8-pole - SOLD TenTec 282 250Hz 6.3mHz IF 6-Pole $55 plus shipping INRAD OMNI-VI/VI+ Roofing Filter Modification Kit NOS - Includes factory wired circuit board with #763 60
After modifying my two OMNI-VI+ transceivers with the INRAD roofing filters, I have one last NOS kit that is surplus to my needs. The original cost was $175 plus shipping. These filters make a BIG di
Richard, I have a 219 250Hz filter for the 9000.750kHz IF available for $50 shipped. It is the later faraday-style (shielded) filter. May have been made by Inrad. 73 Bill N4LG 73 Bill N4LG At 01:49 P
TenTec 288 1.8kHz 6.3mHz IF 8-pole $45 plus shipping TenTec 282 250Hz 6.3mHz IF 6-Pole $55 plus shipping INRAD OMNI-VI/VI+ Roofing Filter Modification Kit NOS - Includes factory wired circuit board w
Enzo, My Orion-II had exactly the same symptoms, on a couple of occasions. The master resets helped for a while, then the same problem came back. Looking at the DC power cable connector, it was fine.
A well-controlled applicator is the DeoxIT D100L-25C Needle Dispenser. It will allow a fraction of a drop to be applied to any surface. 73 Bill N4LG https://www.parts-express.com/caig-deoxit-d100l-25
Hi Dale, I happen to have a few filters left over from upgrading my OMNI-VI+ to Inrad filters. They are: 288 SSB 1800Hz 6.3mHzIF (PBT) 221 CW 250Hz 9mHzIF 282 CW 250Hz 6.3mHzIF (PBT) I'll take $60ea
Greetings, I have a few filters left over from upgrading my OMNI-VI+ to all Inrad filters. For sale are: 288 SSB 1800Hz 6.3mHzIF (PBT) 221 CW 250Hz 9mHzIF (shielded metal type) 282 CW 250Hz 6.3mHzIF
Mike, I really don't know if it would work on a Corsair-II; or certainly not without a lot of thought and planning. For the OMNI VI it is plug-n-play, for the Corsair-II it would likely take some mod
Greetings, I am making room in my station for a couple of new rigs. The following radios are full working sets, free from issues, and have been kept in a temperature and humidity controlled environme
Greetings, I am making room in my station for a couple of new rigs. The following radios are full working sets, free from issues, and have been kept in a temperature and humidity controlled environme
As long as you have it open for a battery change on the front panel, you might as well change the battery on the antenna tuner. 73 Bill N4LG At 11:47 AM 9/30/2019, you wrote: My O2 says â??battery fa
Hi Mike, Sorry I didn't get to you sooner about the Corsair-I 1.8kHz, 500Hz & 250Hz filters. I'll take $65ea for one, $55ea for two, or $50ea for all three and throw in a four-pole filter. Add $7.90
LAST CALL This Corsair-I and VFO-230 parts sets are heading for e-Bay Monday. If you need any components or parts, or the entire unit, contact me. prices are very reasonable. 73 Bill N4LG Shack and S
For Sale, as a complete package or separately: TenTec Hercules II Amplifier Model 420 sn#10A10031 - Excellent condition with original TenTec foam-in-place box and manual. Puts out 550W+ on every band