For Sale at reduced prices, as a complete package or separately: TenTec Hercules II Amplifier Model 420 sn#10A10031 - Excellent condition with original TenTec foam-in-place box and manual. Puts out 5
Hercules-II and cables - SOLD For Sale: TenTec 9420 Power Supply 100A sn#70A10072 - Powers the Hercules Amplifiers plus an Orion, OMNI-5/6, Paragon or Corsair transceiver. Set for 240VAC operation. E
Shack and Shop Cleaning: I have a 560 Corsair-I donor set that I am parting out. It was a working radio whose case was in rough cosmetic shape. I removed and used the PTO, knobs and one of the five t
Gary, Is the RTC battery still providing energy? 73 Bill N4LG At 09:49 PM 11/28/2018, you wrote: H Greetings: I have an Omni 6 that starts boot up, goes through the process of turning the S meter lam
Carlos, I recently repaired a Delta 580 that had no audio output. Inspection found that the LM-383 had a corner blown off. I ordered a couple of the LM-383 AF amps and replaced the defective one. The
TT'ers, Someone have a junker or parts donor Corsair-I/II? I have two Corsair-I's on the bench for repairs looking for parts. I am in need of an audio board, the OFFSET switch, the ALC knob, and seve
Hello Everyone, I am in the process of restoring a tech-special Delta 580 that was chopped up during a PTO rebuild attempt. The PTO was seized up from form of crystallized grease stuff, and I will be
Hello, I have a 580 Delta that has a dirty bandswitch. TenTec warns us not to use DeOxit or other general purpose cleaner/lubricants on their switches. Does anyone know what cleaner/lubricant product
Ken, I have only seen the warning in the TenTec manuals for the OMNI-A/C/D, Delta, Argosy, and Corsair family that use the plastic enclosed rotary switches. I vaguely recall something about washing a
I am looking for a PTO repair kit for a TenTec PYO. I have a Delta that has some issues, and was hoping one of you folks had a kit that was excess to your needs. Send me your price plus shipping to 4
Beware of the phishing attempt you may receive (see below). Someone has harvested names from this list and is targeting "ETO_Alpha" and "TenTec" members. 73 Bill N4LG Delivered-To: n4lg@qx.net DKIM-S
Carl, Using the method you propose (parallel receiver), how do you make the SDR track the received frequency so that it signal heard is always centered in the panadapter view? 73 es tnx Bill N4LG At
TenTec items for sale: 1) Hercules-to-Corsair/OMNI/Paragon remote-band-switching cable KIT to build a model 236 cable. Contains one 15-pin (5x3) molex male connector, and one 25pr cable with a DB-25
Per Barry N1EU's advice to beware: These two filters are 100% tested and working as per Tentec specifications. They were pulled from my personal rig and I guarantee them. 73 es tnx Bill N4LG Model 28
Since these didn't sell earlier, I've lowered the price to the TT list: Model 282 Tentec 250Hz CW Filter 6.3mHz IF for Corsair, Paragon and OMNI-5/6. $50 shipped. Model 288 Tentec 1.8kHz SSB Filter 6
In my humble opinion, a suitable alternative to the Corsair-II is the currently available Elecraft K2 with the 100W PA. http://www.elecraft.com/k2_page.htm Elecraft products are made in America, they
The point of my posting of Elecraft as an alternative to the Corsair, is that you cannot buy a new TenTec product at this time. 73 Bill N4LG At 04:28 AM 11/26/2016, you wrote: Dave, that was exactly
Barry,, Yes, I have both birdies - same freq, same level, no ant. 73 Bill N4LG At 10:01 AM 11/15/2015, Barry N1EU wrote: I hear a very strong birdy (s5 with antenna disconnected) on my Omni 6+ at 213