I have a few users that are in fact running my software with windows on a mac. I have had some people say it works with using linux and wine and others say it does not. Carl Moreschi N4PY 121 Little
I don't know about the Ghiel chip, but my N4PY Paragon chip will make the Paragon talk Icom over the serial port. So all you would have to do is configure logger32 for an Icom radio and it would work
Make sure TXloop is not turned on if TXOUT and TXEN are not connected together. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: <K9RT@aol.com> To: <
No, there were no options for filters on the c-21. The filtering is all done at audio so I would look for things like loose connectors and such. Maybe the filter switch is just dirty from lack of use
If you will email this database file to me, I will make a converter to put it in N4PY format for you so you can load it into your Orion II. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays
Eric, This was the reason for tentec coming out with V2. As I understand it, the following was tentec's position on this. There was a timing problem in V1 that could not reliably be fixed. V2 institu
The Paragon II hardware is only slightly improved over the Paragon. Neither radio has an internal tuner or keyer. The main difference between the Paragon and Paragon II is the Paragon II had more str
The 160m converter converts 1.8 mhz to 3.5 mhz. So you tune on the 80 meter band. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Mark Choate" <aa0
I had something similar problem happen to my OII when I first received it. It would go almost deaf. I changed antenna settings to antenna 2 and right back to anetnna 1 and the problem never occurred
What firmware do you have loaded? You may need to do a battery reset followed by a main reset. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635 It has developed a str
No, you do not need RTS or CTS. The omni VI is completely CI-V compliant. You need to set the correct baud rate and the correct CI-V address in your program that is trying to access the Omni VI. Thes
No, you are not missing anything. Either connection works the same. The only advantage of the mini-plug connection is you can parallel connect up to 4 CI-V type radios connected over the same serial
There's more specs to crystals then just the frequency. There is the capacitive load either series or parallel and whether the crystal is operated at the fundamental or a harmonic and also the case t
Yes. They use different sockets. The remote pod form the Oiron does not plug into the serial port. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635 II. for the comput
The pegasus pod will work with an Orion. I am using a pegasus pod on my Orion. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635 http://track.netzero.net/s/lc?s=197335
The first local osc outputs a frequency of 45 to 75 mhz (45 mhz higher than the operating frequency) in 2.5 khz steps depending on the operating frequency. This frequency is controlled by the onboard
The AT-200PC autotuner from LDG, when used in conjunction with my rig control software, ends up following the rig without having to transmit. You just have to tune one time on each frequency and then
The horizontal lines just represent the maximum range the bandwidth rectangles can move. The break in the line is just to separate the line for the main receiver side and the sub receiver side. If yo
The DSP code in the firmware is doing all the changing to accomplish this. Very little is happeining electronically. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original
It is coming some time soon. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Jeff Frank" <jafrank@nyc.rr.com> To: <tentec@contesting.com> Sent: Tue