The program has a frequency calibration procedure. You run this procedure at 10 mhz. Once the error at 10 mhz is determined, the error at all other frequencies can be computed. When you run diversity
My N4PY Paragon chip disables the DST feature of the clock. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "CSM(r) Gary Huber" <glhuber@msn.com> To
You can use CW Skimmer and do all this with my N4PY software, an Orion, and N8LP's LP-PAN panadapter. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From
I see the archives now have all the files for the Orion. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "John Graves" <jh.graves@verizon.net> To: "
I would make sure that TXEN and TXOUT are not reversed. Other than that, it sounds like you have a fault in the amp. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original
Reverse CW (on the Orion this is UCW) uses the upper sideband side of zero beat. In reverse CW, as you tune up in frequency, the pitch of CW signals goes down. In LCW mode, as you tune up in frequenc
You only need to install the latest firmware version to get completely up to date. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635 will install Get because the have
I do not have the new memory chip in my Jupiter. I installed the PLD update and then installed version 1.30. It does not have the CW keyboard feature or CW decoder in it. I thought I could load 1.30
The 538v1300.ruf file is for Jupiters that have the extra memory and it has both personalities in it. The 538cwv1010.ruf file is the CW personality for Jupiters that have the old memory chip like min
John, It's been a little while now. Are you still sure you have fixed your RIT problem? 73, Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "John T.
There are 12 torque screws you have to remove from the back. All these are along the edge of the cover on the back of the radio. Then each cover has 4 large side screws to remove. That's it. Carl Mor
By the way, all my software supports the topten devices Yaesu interface through the parallel printer support. And I have a parallel printer driver in my software so that the parallel printer port eve
I have just added code to my Orion program that can fake out a K3 interface so the N8LP's panadaptor can work with an Orion using my N4PY software. Carl Moreschi N4PY 121 Little Bell Drive Bell Mount
Ken, W8KEB, is now a silent key. He was from Ohio but never had any kind of store. He was just a great guy that I will always remember. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC
The QSK loops are just signal cables and do not carry RF. The simple radio shack shielded audio cables with RCA phono connectors on each end work fine. I have been using them for years. I assume you
Yes, it is available now with LP-PAN and my Orion software. My Orion software fakes out LP-PAN into thinking that the Orion is a K3. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North
I just want to annouce that all my software has been converted to 32 bit software. As 32 bit software, the programs runs smoother, use less CPU, and run faster. See my webpage at www.n4py.com Carl Mo
The bypass switch on the transverter was designed for 100 watts. I believe you are ok at 200 watts doing this but I would watch the SWR at the rig. If it suddenly jumps then it was not ok. Carl Mores
Does the A/B button work Ok instead of REV? Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Dennis Doran" <wb8wtu@gmail.com> To: <tentec@contesting
You connect the TXOUT jack to a line that will key the amplifier. The amplifer should then have some kind of key out jack on the amp. You connect that back to TXEN on the radio. Carl Moreschi N4PY 12