I use my Omni VII to drive my Acom 1000 on 6 meters. I can transmit a 1000 watt signal on 6 meters using this combo. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original
You have to leave it in some remote mode when you leave the shack. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "jkelly@home" <jkelly@bellatlanti
Try using a much slower AGC. The AGC can be so fast that it makes all the signals the same strength. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From:
The procedure as you outlined it essentail turns off AGC and puts you in a completely manual AGC mode. This is how my old Collins 75A1 (circa 1949) has to be run to listen to SSB and CW. I would not
I thought I would share with this group how I matched a 30 meter loop I made to use with my Omni VII and Orion. I made a full wave delta loop for 10.1 mhz. I used 14 gauge wire and erected the delta
Just reduce the RF gain enough to get rid of excessive band noise and operate the rig normally. I run mine with RF gain at about 95 but this varies greatly with band noise and antenna. I usually have
Actually the first cut I made was 10 feet and then I have 8 1 foot jumpers! Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635 _________________________________________
My N4PY Orion Software has a procedure to do this. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Kim Elmore" <cw_de_n5op@sbcglobal.net> To: "Tent
So what was the final verdict. Do you have a chirp or not? Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "VE1BN" <ve1bn@eastlink.ca> To: "N4YG" <n
But Jeff was in the reverse situation. Jeff was the buyer and not the seller. If he had mailed a postal money order, would things have gone any better? As far as selling, I like paypal. It is immedia
Again, this is why I like paypal. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "AD5VJ Bob" <rtnmi@sbcglobal.net> To: "'Discussion of Ten-Tec Equi
Tentec stated a month or 2 ago that after they are finished with the rx400, they will do another Orion firmware update. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Origin
This is true for the Orion II. It is also true for the Orion when using V2 firmware. However, the original V1 firmware does have the notch inside the AGC loop. So it definitely can be changed with fi
My N4PY Orion program will do this job very nicely. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "fraz1" <fraz1@bellsouth.net> To: "Discussion of
Just get a USB to serial converter from keyspan at www.keyspan.com along with my software. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "fraz1" <
Do a battery reset by powering off and holding the VFOB LCK button and powering on until it says "battery failure". Then do a normal reset by holding the "Main RX/TX" button the same way. Then do a p
If you right click on the split button while in the 10 meter FM repeater area, the down 100 split offset is automatically set. This is also true for 6 and 2 meters when using a radio with this capabi
500 euros is about $750. I think you have the exchange rate backwards. Also, if he pays with paypal, he can specify the amount in US dollars to get you the correct amount. Carl Moreschi N4PY 121 Litt
Many are confusing the term "open source" with free software. "Open source" means the source code to create the software is available for anyone to modify and make changes they want. The free softwar
I will be at the Dayton Hamfest in booth 227. Stop by and say hello. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 _______________________________________________ TenTec maili