My first transmitter was DX60. It ran 90 watts input power and about 60 watts output from a single 6146 on CW. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Messag
Did you do the battery reset? You power off, press and hold the VFO B LCK button, power on, and continue holding it until the radio says "battery failure". Carl Moreschi N4PY 121 Little Bell Drive Be
My bet is the battery reset will fix it. I have had this problem and the battery reset fixed it. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Tő
Wow, I guess life is good! Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Mike Bryce" <prosolar@sssnet.com> To: <k4qo@earthlink.net>; "Discussion
I am almost ready to put out 32 bit versions of all my N4PY software. Previously, all my software was 16 bit. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635
There is an SSBRTTY.DAT file that allows you to define the digital area inside the CW area. Defining this file properly addresses the exact issue you are talking about. Carl Moreschi N4PY 121 Little
500 euros is about $750. I think you have the exchange rate backwards. Also, if he pays with paypal, he can specify the amount in US dollars to get you the correct amount. Carl Moreschi N4PY 121 Litt
Many are confusing the term "open source" with free software. "Open source" means the source code to create the software is available for anyone to modify and make changes they want. The free softwar
Do a battery reset by powering off and holding the VFOB LCK button and powering on until it says "battery failure". Then do a normal reset by holding the "Main RX/TX" button the same way. Then do a p
If you right click on the split button while in the 10 meter FM repeater area, the down 100 split offset is automatically set. This is also true for 6 and 2 meters when using a radio with this capabi
I thought I would share with this group how I matched a 30 meter loop I made to use with my Omni VII and Orion. I made a full wave delta loop for 10.1 mhz. I used 14 gauge wire and erected the delta
Just reduce the RF gain enough to get rid of excessive band noise and operate the rig normally. I run mine with RF gain at about 95 but this varies greatly with band noise and antenna. I usually have
Actually the first cut I made was 10 feet and then I have 8 1 foot jumpers! Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635
My N4PY Orion Software has a procedure to do this. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Kim Elmore" <cw_de_n5op@sbcglobal.net> To: "Tent
So what was the final verdict. Do you have a chirp or not? Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "VE1BN" <ve1bn@eastlink.ca> To: "N4YG" <n
But Jeff was in the reverse situation. Jeff was the buyer and not the seller. If he had mailed a postal money order, would things have gone any better? As far as selling, I like paypal. It is immedia
Again, this is why I like paypal. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "AD5VJ Bob" <rtnmi@sbcglobal.net> To: "'Discussion of Ten-Tec Equi
Tentec stated a month or 2 ago that after they are finished with the rx400, they will do another Orion firmware update. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Origin
This is true for the Orion II. It is also true for the Orion when using V2 firmware. However, the original V1 firmware does have the notch inside the AGC loop. So it definitely can be changed with fi