You can get very nice transverter support with the operating frequency being displayed with my N4PY Orion control program. Also, with my program, you can have any step size you want including 9 khz.
Version 2.17 of my N4PY Pegasus/Jupiter Control program is now available. All registered users should now have it. Highlites of version 2.17 1) Added 5 CW memory tag edit boxes to personalize the M1
Fernando, If you use the RTTY modes instead of USB, the speech processor is automatically turned off when you go to RTTY. You can define an RTTY mode to really use USB and have a zero offset for the
Duane, You are describing the kind of things that go well with a control program. My N4PY Orion control program allows you to define a remote pod key for "Up". To do what you describe, all you do is
Yes, the "Up" function can be setup to be done on the PC keyboard numeric keys to make a pseudo pod. Also, my program automatically handles the audio setup. With DUAL turned off, the VFO A receiver i
I have an RX-330 that I have now finished software development for that is excess to my needs. This is a fantastic receiver that is very similar to the RX-331. See the TenTec website for a full descr
I finally got around to trying out DRM. I fired up my RX340 and got the freeware program "Dream" installed. I have been listening to a station from Canada at 9800 kHz for the past several hours. I am
Paul, All you have to do is take the audio from pin 2 and ground from pin 1 of the DB15 on the RX340 and run it into the PC sound card. You may have to reduce the output level from the RX340. I used
You can use an rx320, Pegasus, or Jupiter for DRM by making a small mod to bring the 12 kHz IF out to the input of your PC sound card. But the Orion has a 14 kHz IF and so cannot be used for DRM with
Yes, I now think the 14 khz IF in the Orion would be fine. I experimented with the RX340 and found I could move 3 khz either side and Dream would still decode. The Dream decoder displayed a frequency
My N4PY software will send signals to a topten device attached to the parallel port to control antennas. People have been using this with all radios I support for 4 years. Carl Moreschi N4PY Franklin
I find the hardware noise blanker in the Orion is fantastic. I have an intermittent power line buzz that shows up here once in a while, and the Orion hardware noise blanker is the only thing that com
That's great information Mark. Thanks for sharing it with us. 73, Carl Moreschi N4PY Franklinton, North Carolina n4py@earthlink.net -- Original Message -- From: "Mark Erbaugh" <mark@microenh.com> To:
That would have to be a firmware change. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Lynn Lamb" <w4nl@charter.net> To: "Ten-Tec Reflector" <tentec@contesting.com> Sent: Monday, J
You can control the Argo V very nicely from a computer with my N4PY control program. See www.n4py.com. There are no alternate sources for the firmware. 73, Carl Moreschi N4PY Franklinton, NC -- Origi
The latest N4PY Orion software version is 1.09. Version 1.10 is coming out on August 1. It will have several new features. 73, Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Jeff Gr
No, I'm sorry but it does not have LCW for the Argo V. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Lynn Lamb" <w4nl@charter.net> To: <tentec@contesting.com> Sent: Monday, July 26
There are huge differences between the Delta and Delta II. Probably the biggest difference is the Delta II has general coverage receive. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From
You must also be at 1200 baud for Paragon II. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Rick and Karen Bunn" <RRBunn@cox.net> To: <tentec@contesting.com> Sent: Monday, July 26,
Mark, I cannot reproduce your audio problem either. My guess is you have some setting set to a different value then other people that is necessary for the problem to show. 73, Carl Moreschi N4PY Fran