FSK is strickly for RTTY or modes where only two tones are used. It can only produce two tones - a mark and a space. For the PSK31 type modes, AFSK must be used. Carl Moreschi N4PY Franklinton, NC --
My N4PY Orion Control Program is now fully functional and available to operate the TenTec Orion completely from computer control. Highlites of using the N4PY Orion Control Program are: 1) You can use
Let's all get on 5371.5 carrier frequency at midnight. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: <wmlb@sbcglobal.net> To: <Tentec@contesting.com> Sent: Thursday, July 03, 2003 2
No, it's not a concern at all. When you load firmware into the Orion, the RUF file must follow an exact format or it will not load. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "M.
I remember the smell of those U control model airplanes and all those Cox .049 engines. So all I need to do is get some Castor oil and cut the grass. Sounds very fun and nostalgic. Carl Moreschi N4PY
Of the ones you listed, only the 218 will work in the Orion. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Josh Kelly" <jkelly@hiwaay.net> To: <tentec@contesting.com> Sent: Sunday,
My LSB works. The RIT does not come on until I actually tune in some RIT. It is off if the actual RIT value is zero. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: <jeff@ke9v.com> To
I have full rig control from the computer for the Orion. See my Orion Control Program at my webpage of www.n4py.com. 73, Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "jbattin" <jba
I made a mistake on my orion shack picture. It is on www.qrz.com and then look up my call. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Jim FitzSimons" <cherry@getnet.net> To: <te
I am having a hard time understanding where this propagation frequency error could come from. It seems to me that if WWV was at 15 mhz and I was receiving a 14.999990 frequency, this 10 hertz frequen
Yes, but that would be a very short lived changed. The average over a few seconds would still be right on or we are in a different time reference. Carl Moreschi N4PY Franklinton, NC -- Original Messa
Bill, Yes, WinXP Pro is fine. You don't need any diskettes so $35 is also fine. The diskettes are just for people that don't have or know how to use email. Yes, I like to see apicture of the Chinese
Jerry, That's all well and good. But the fact that the frequency measurements made on my Orion and several others mentioned earlier in this thread are so repeatable says there's something wrong in th
Version 2.08 is now available. All current subscribers should have received it by now. It features transmit capability for the new 5 mhz band. Carl Moreschi N4PY Franklinton, NC
Scott, That's good to know. I didn't know they measured at the 26db down points. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Scott Prather" <sdprat@worldnet.att.net> To: <tentec@
You can plug them in in either direction. It does not matter. Carl Moreschi N4PY Franklinton, North Carolina n4py@earthlink.net -- Original Message -- From: "M.Todd Miskel" <kd7efq62@hotmail.com> To:
I've been playing with the RF gain control on the Orion trying to determine why the background noise does not diminish as the RF gain is reduced. What I believe is happening is the DSP AGC is compens
Jim, I just ordered the HP Z3801A GPS receiver also. I'll add something in my Orion software to allow you to match the Orion to the rx340's frequency on a per band basis. Carl Moreschi N4PY Franklint
Bill, All centaurs have loud fans. When I had mine, I did 3 things to help. I added a 100 ohm 20 watt resistor in series with the fan. This slowed it to half speed and made it much quieter. I was wor
I received my HP GPS receiver today. I have it all installed. I used Jim's method to hook it up to the rs232 port to the computer and it works fine. I now have a 10 mhz frequency standard that sets m