Bill, This was done about a year ago or so on this reflector. But I will try from memory to give the genealogy. After the Omni C, the main transceiver evolution continued as follows: Corsair Corsair
My email address is n4py@earthlink.net My webpage is www.n4py.com. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: <W9MWS@aol.com> To: <tentec@contesting.com> Sent: Sunday, December 1
My son had my centaur for contesting for about 6 months. I had just put 572B's in it. The tubes lasted about 6 months. I don't know if he had mistuned them or not but we never saw any more power outp
The RF gain control on the Orion with firmware 1.372 now reduces AGC threshold first, then as the RF gain is continued to be lowered, actual RF gain is reduced. This has the affect of making the RF g
The amp keying line is energized about 10 to 20 msec ahead of keying and is not adjustable. This should be very safe for amp relays. Only the drop out time is adjustable. Carl Moreschi N4PY Franklint
I have always run my Orion with keying loop 1 on and keying loop 2 off. I do not have anything hooked up to keying loop 2. I have not experienced the keying loop problem with my Orion and ACOM 1000.
C82 and the 200K rsistor are in the ACOM 2000. This is an ACOM mod and not an Orion mod. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Tommy" <aldermant@alltel.net> To: <tentec@con
I have sent out version 2.19 of my Pegasus/Jupiter/Argonaut V/Rx320/Rx340/Rx350 control program. All registered users should now have it. See my webpage at www.n4py.com. Highlites of Version 2.19: Ve
I don't have any immediate plans for Yaesu but things could change. 73, Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: <W4ABW@aol.com> To: <tentec@contesting.com> Sent: Monday, Novem
Depending on the windows version you are using, the slider ID's for these controls in the old tentec software had a conflict. One solution is to get my N4PY software. Carl Moreschi N4PY Franklinton,
I just released Version 1.12 of my Orion Control Program. All registered users should now have it. See www.n4py.com. Highlites of version 1.12 1) Added an "ssbrtty.dat" file to control the RTTY and S
Steve, The CW keyboard keying works fine with windows 98 and windows ME. Also, the K1EL support I have added fixes CW keying for all OS's. The frequency tuning with the pod with the pegasus and jupit
It sounds like he needs a keyer that can adjust all the keying delays to get around this. The K1EL winkey keyer has parameters to adjust delays both ahead of and after keying. There is even a special
Changing to a USB port will not help at all. The Orion serial baud rate is fixed at 57600 baud. The problem is the Orion is not fast enough to keep up with commands from the program because the Orion
There is another K1EL keyer that runs standalone but I'm not sure if it is as versatile as the winkey. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "NJ0IP" <Rick@dj0ip.de> To: <ten
Joe, The lag is not seen on the Jupiter and Pegasus, only the Orion. The Orion just has so much to do. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Joe Giacobello" <k2xx@swva.net>
Rick, To answer your first question, CW QSK DELAY has nothing to do with keying the amp. This is the delay before the receiver comes back on after transmitting. I assume you have EXT T/R connected to
Doug, Thanks for the very interesting story!!! 73, Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Douglas" <sparks06524@yahoo.com> To: <tentec@contesting.com> Sent: Thursday, Novemb
WriteLog interfaces to with my sofwtare and also directly to the Jupiter. I don't know if N1MM contest software will work with a Jupiter. Carl Moreschi N4PY Franklinton, NC -- Original Message -- Fro
Most logging program will work with the Pegasus only with soem control sofwtare to control the pegasus such as my n4py software. But the Jupiter has two complete and different command sets. It can be