It also depends on band noise strength. If the band noise is strong enough, it will cover up the rs232 noise. And it also depends on what program is running and how often it polls the Paragon and sen
I would just use the key line on the accesory cable. If my memory is correct, this is the black female RCA jack omn the acessory cable. This key line is great for straight keys and external keyers si
57600 baud, 8 bit, no parity, RTS/CTS signalling. Carl Moreschi N4PY 121 Little Bell Dr Hays, NC 28635 www.n4py.com Just got an Omni VII today. Trying to get it to talk to N1MM or vice versa. Nothing
In fact my N4PY Paragon chip makes a Paragon II out of a Paragon. I did the firmware for the Paragon II for Tentec my N4PY Paragon chip is very similar to the Paragon II firmware. The biggest problem
My latest version of my N4PY Orion software now has an option to control the Tentec Eagle. The Eagle must be at firmware 1.682 or later. See my webpage at www.n4py.com Carl Moreschi N4PY 121 Little B
The hardware AGC does not come into play at all on the Orion and Orion II until a signal is greater than S9+20 to S9+30 somewhere in the 9 mhz IF passband. If hardware AGC pumping is occuring, the fi
My N4PY software will control the rx350. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com Hello John, If you look at a picture of the RX-350, you will see that it looks just like
The Jupiter does not need a magnetic breaker but the Pegasus does need one. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com -- Original Message -- From: "Rick - NJ0IP / DJ0IP" <R
The Orion comes with a standard 2400 hertz roofing filter for SSB and a standard 1000 hertz roofing filter for CW. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com Barry, Most of
Yes, the 2.4 khz roofing is automatically selected when your DSP BW is 2.4 or lower. If you put the 1,8 filter in, that will come on when you go to 1.8 or lower. I believe my son, N4YDU has a 1.8 khz
I have been using an Astron 35M for all my shack 12 volt power since 1988. This supply has been on continuously since 1988 except for when I power down and disconnect during lightning storms. The sup
I would look into the low pass filter board relays that switch in the low pass filters. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com My Omni 6+ suddenly has zero power output
The easiest way is to use my N4PY software and get the receiver as outlined by WD5FUN on my webpage. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com Hi All , I would like to know
The directions for this are in the N4PY help file for the Pegasus Plus program. Just search for "Using the RX-320, RX-340, Pegasus, or Jupiter with the Omni VII". Carl Moreschi N4PY 121 Little Bell D
Years ago, I replaced my amplifier relay in my Omni A series B with a 2N2222 transistor. I just used the relay pick voltage to fire the transistor. As long as your amp does not draw more current than
Your crystal for the 28.5 band may not be starting. It may come to life by adjusting the load trimmer for that crystal. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com I have a O
They are both great radios. The biggest difference is on CW. The Flex radios have no CW QSK and the internal keyer in the Flex radios has latency which makes using the internal keyer difficult. Carl
The big thing with Flex is the panadapter. The SSB performance of both the Orion and Flex 5000 is great. My software can easily provide a great panadapter for the Orion with LP-Pan if you want to do
You almost cannot hear the fan at all. I can only hear it by turning the audio all the way down. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com My first question to those now us
There's a battery behind the front panel of the Orion. It may need to be replaced. Follow the old instructions on the Tentec site for how to modify the Orion for the Version 2 sweep to get to the bat