I said traditional wattmeter. I am referring to inexpensive wattmeters that only measure voltage. Carl Moreschi N4PY 121 Little Bell Dr Hays, NC 28635 www.n4py.com No, a true wattmeter (Bruene design
This could be RF feedback getting into the Orion. The fact that it is band sensitive points to this. Carl Moreschi N4PY 121 Little Bell Dr Hays, NC 28635 www.n4py.com I have noticed a subtle characte
Have you done a complete reset to the Orion? 1) Power off Orion. 2) Power On holding the VFO B LCK button. 3) Continue holding LCK button until the radio says "Battery Failure". 4) Power off Orion. 5
Come down I-77 south to I-81 South. I-81 will take you to route 40 West. Route 40 West goes right by Sevierville on the way to Memphis. Carl Moreschi N4PY 121 Little Bell Mountain Dr Hays, NC 28635 w
The 1209 converts 144 to 50 mhz. You will enjoy the 1208. I used one with my Orion for a long time and it worked very well. Yes, just keep the power at 5 watts and all will work well. Be very careful
I was referring to the 1209, not the 1208. The 1209 is a 6 meter transverter that converts 50 mhz to 144 so you can use a 2 meter radio and get 6 meters. I never had a 1209, just a 1208. And of cours
I now have a new capability with my N4PY software and any radio supported by N4PY software such as the Tentec Omni VII and Jupiter. If you add a Flex radio to the mix (and this could even be a used S
The reflector has been working well for me but I also got 2 emails from Morine saying the same thing. Carl Moreschi N4PY 121 Little Bell Mountain Dr Hays, NC 28635 www.n4py.com Hello I have not been
Yes, my N4PY software can link any radio supported with N4PY software to any SDR radio that works with PowerSDR. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com the new n4py soft
You need an SDR that is capability of making a panadapter screen using powerSDR. This requires a Flex radio of some type. I believe SoftRock radios will also work. The key is they must be capable of
Yes, that's exactly what it sounds like. The internal battery in behind the Orion front panel. Actually, it's in the front panel when you remove it. Carl Moreschi N4PY 121 Little Bell Mountain Dr Hay
John, Try this: 1) Turn on TXloop for antenna 1 on the orion. 2) Connect TXEN to TXOUT on the Orion. Does the Orion now key when you try to transmit? It should. If that works, then connect TXOUT to t
John, What I'm trying to do is diagnose what is going on. If you turn on the Orion keying loop and do not connect anything between TXEN and TXOUT, transmit will be blocked. If you then jumper TXEN an
It sounds like the amp does not connect TXEN to TXOUT when its antenna relay switches to transmit. If you have the amp in standby but still connected to TXEN and TXOUT, does the Orion transmit normal
Just make sure you do not have TXEN and TXOUT cables reversed. If you do you would have the symptom you see. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com -- Original Message -
The previously announced capabilty to use a Flex panadapter with my N4PY software also works with the TenTec Omni VI. My N4PY Icom software also supports the Omni VI. If you add a Flex radio to the m
All my versions have this capability. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com Is that only for Orion version, or is it also in the ICOM and Pegasus version? Best Wishes R
The best bang for the buck is to find a used Pegasus for $500. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com Hello to the list, I am looking to upgrade my station which current
You can add N8LP's LP-Pan to the Orion or Orion II. You need to make a mod to the Orion that is written up on VE7TK's website and then use my N4PY software to integrate everything. But this works ext
No. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com Is any after market manufacturer making a fully integrated stand alone display such as the one available for the Elecraft K3 t