I don't remember if the 301 knob had an adjustable drag on it or not. But if you run the O7 with my N4PY software, I have a software parameter you can set to adjust the knob sensitivity. This is an e
Just plugging a mic into the 234 and supplying 13.8 volts to the back phono connector of the 234 should cause blinking of the red LED when speaking into the mic. If you don't see any blinking when oy
When first installing this chip, an initialization procedure must first be run. With the new chip installed, do the following: 1) Power on the Omni V 2) Press the reset button on the right hand side
I still have chips for both these radios. The Omni V chip converts the radio almost to an Omni VI. The chip for the original Paragon makes the Paragon almost be a Paragon II. For the Paragon, I need
There are a couple of plug in connectors that almost everything in the Orion comes through behind the Orion front panel. I have fixed a couple of Orion problems by simply removing the front panel and
It was a new Microphone and a sound card replacement device that plugs into your USB port. This device has a cable on it that will plug directly into your Tentec accessory connector. It makes hooking
Yes, there is. You need to remove the Orion front panel to see it. Carl Moreschi N4PY 121 Little Bell Mountain Drive Hays, NC 28635 www.n4py.com Hi all....one of my Orion's has a problem and I am not
I may be wrong, but I think this is to set the Orion's frequency dead on the mark. It's either that or the hardware mic gain control. Carl Moreschi N4PY 121 Little Bell Mountain Drive Hays, NC 28635
There was a pot on the bottom of the C21 you access through a hole in the bottom. This was for sidetone volume. I just can't remember if there were 2 pots with one also being for pitch. The original
The 610 keyer is an accessory for use with remote operation. You use the keyer at a remote site and key with it using paddles. The keyer generates characters just like they were typed from the keyboa
The mic gain in the Orion N4PY program is remembered by band. You can set the mic gain for each band one at a time in the N4PY SSB settings window and the program will remember these values when retu
I'm looking for a tentec model 1210 2 meter transverter. If anyone has one that is surplus to their needs, send me an email. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 www.
N4PY software is not available under Linux. But it does handle the audio both ways and connects via an IP address. Carl Moreschi N4PY 121 Little Bell Mountain Drive Hays, NC 28635 www.n4py.com I wasn
I have had a few intermittent problems with my Orion over the years. I always fixed them by removing the front panel on the Orion and unplugging and then replugging the main connectors there. Almost
Logger32 is another good one for the Omni VI. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 www.n4py.com Jim, Thank you very much for the good information. And yes I have thin
My trusty Orion and LP-Pan setup is now for sale. The Orion is modified to bring the main receiver 9 mhz IF out to LP-Pan and also to bring the 455 khz IF out to a converter that converts this to 9 m
What happens if you just turn the radio off and then back on? Does that get it working again? Carl Moreschi N4PY 121 Little Bell Dr Bell Mountain. Hays, NC 28635 -- Original Message -- From: "Bob Clo
Well if my software does not have ot rebboot to get things working again, I would say the Oiron has a problem with losing serial port communication in this scenario. Thanks and 73, Carl Moreschi N4PY
The 238C new tuner is a 238B with a built in cross needle watt meter and a better scale to log your settings with. It is still an L match manual tuner and it handles 1500 watts very well. 73, Carl Mo
The tentec 538 tuner is a reversible L. That means it has 2 configurations for the L. One for high impedance and one for low impedance. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC