Replace the battery inside the radio. Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py.com Good Morning all, i have just resurrected from the self my Paragon 585 as a back-up t/rx t
The shorting link between TXEN and TXOUT is only needed if TxLoop is enabled in the menus. If TxLoop is enabled and no shorting link, then the radio will be prevented from transmitting any power. Tha
All that strongly suggests the key line input is shorted some place. Turning off the keying loop stops it because that just means the transmitter has been keyed but is waiting for TXEN to go to groun
My N4PY Pegasus Plus can control the Jupiter just like it was a Pegasus, therefore not needing any display at all. Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py.com On 10/9/2021 1
Hi Mike, I have a one wire mod to bring the Orion sub-receiver antenna connection out to the spare jack. This then connects to the SDRplay antenna connection. You then run the SDRplay with HDSDR. My
If the RTL-SDR can be controlled with HDSDR, then everything I told you is still correct. 73, Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py.com On 3/8/2021 3:05 PM, Michael Tortor
What is the voltage inside the radio after the power connector? It may be a volt or 2 lower if the connection is not a good one. And these voltage need to be measure while transmitting full power. Ca
But how about on the inside of the radio on the other side of the connector? Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py.com Sent from my iPad __________________________________
No, I mean inside the radio. Remove the cover and measure the voltage inside the radio, after the plug. The plug itself is notorious for having a big voltage drop. Carl Moreschi N4PY 127 River Moss W
I remember hearing this on my Omni A series B. And that did not have the digital display. Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py.com One of my Drake TR5s did the same thing
You have to remove the antenna to hear the pulse at 14.0 Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py.com Sent from my iPhone It is not at all unusual for electrolytic capacitors
My N4PY Icom program will control it fine. Then you can connect all other programs to my N4PY Icom program and all will work well. Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py.co
My N4PY Orion program will send band data via the KPA500 serial port and do the job for you. No band decoder needed. Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py.com I use my Ori
The Paragon II uses an Icom interface. It's CIV address is 2C. The baud rate is adjustable but it must match what you select in N1MM. Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py
The Omni VI uses CIV address 04 at 1200 baud. It uses the Icom interface. Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py.com I think you need to use the Icom Civ for rig control. T
I worked for my first 2 years with a DX60 and HR10. My receiver was a collins 75A1 I found at a flea market for $50. The receiver accuracy made up for the HR10 inaccuracy. I just spotted myself with
The most common filter that most used was the 217 500 hertz filter. It's 500 hertz wide at 6 db points and 1000 hertz wide at 60 db points. Just put that one in and don't worry about it. Carl Moresch
The scheme used in the Tentec radios that have TX EN and TX OUT goes like this. When the radio wants to transmit, it sets TX OUT low. The amplifier is supposed to receive this line and when the anten
The firmware will not allow it. Carl Moreschi N4PY 127 River Moss Way Hertford, NC 27944 www.n4py.com On 1/9/2020 5:03 PM, damichael-- via TenTec wrote: I am interested in trying my Omni 7 at 630m as
The 6.6 mhz filters will not work on the Omni C. The 9 mhz filters will work on the Omni C. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Thank you, Robert KG4KGL ________________