My N4PY software will let you use a Flex control, or a behringer DJ controller or a Tentec pod as a knob. The Behringer DJ controller is the best as it has a great tuning rate, 4 knobs, and many butt
Yo can get an SDRplay for $120 and use my N4PY Software. I have a one wire mod to the Jupiter so you can safely share antennas between the Jupiter and SDRplay. Carl Moreschi N4PY 58 Hogwood Rd Louisb
My N4PY Orion software allows small changes from the ham band allocations for transmit. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Jim M. N4BE Sent from my iPhone _____________
The best way to do that is to purchase an SDRplay receiver. They are only about $100. Then you will also need an MFJ1708SDR to share antennas between the Argo V and SDRplay. Then if you run SDRplay w
A better solution is to use an SDRplay with the Orion. That's how I run my Orion. I do have a screen shot which I can send you. And you can have a much wider panadapter with any of the SDRplay receiv
It's for a separate receive antenna. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Some TT radios have an RCA connector marked as "RX Antenna", together with a "RX / TRX" switch.
Anything that says FTDI is fine. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com http://ve7sl.blogspot.com/2016/02/usb-ptt-line-keying.html 73 F5VBU The Dell machine I am using allo
The antenna connection to the sub-receiver is very obvious when you look at the sub-receiver. You can pull the connector and put another on there that goes to the spare jack in the back. That will do
You can also just run a small rg174 coax from the sub-receiver antenna connection to the spare jack. Then select no antenna at all for the sub and connect an antenna for the sub to the spare jack. Th
There were two different synthesier boards in the Paragon. The original paragons used a Version 3.xx chip that worked with the original synthesizer. The last year os paragons required a Version 4.00
That chip will not work in a recent Paragon and will definitely not work in a Paragon II. Check to see what chip is in your Paragon. If the version starts with a 3, that chip will not work in that pa
Firmware 1.373b5 filters were done by Smith who came from Kachina. Filters in 3.32 were done by Gary Barber. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com I just compared my both
The roofing filters between the Orion and Orion II are physically different. But the job of roofing filters is not critical for selectivity. The roofing filters are for the 2 khz dynamic range. The D
No, I think it means the settings are saved in non-volatile RAM. But I might be mixing that up with the Omni VII. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com 73, Winston K4CWQ S
I just want to point out that my N4PY Orion program will control the Orion very well and make it so the VFO encoder is not needed at all. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py
Finals blown? Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 10/10/2018 2:41 PM, Joe Word wrote: My Pegasus has no transmit output. Receive works fine. No output on any band on
Yes, that is correct. My N4PY software also can add over 60 different functions to the pod buttons. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Joe N9VX
That won't put you off frequency. Do you have a logging program that is communication with the Omni VII? If it is not using RTS/CTS handshaking, it can cause the Omni VII to have an XIT value. You ha
It will work with either port. The radio uses an Icom command set. 73, Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com I could of sworn I ask this before, but I looked in my archive
Hi Rick, That was me. But I no longer have the Acom. See you in Germany. 73 Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 6/9/2018 9:40 AM, Rick@dj0ip.de wrote: Long forgotten,