I have now fully integrated the Woodbox radio Tmate2 with all my software. The Tmate2 has 3 knobs and 9 buttons and you can choose from a list of over 60 functions to set for each control. Additional
You want to take the antenna in connection at the main receiver, and bring that out to the spare jack. Then make another jack of some type and return to the main receiver antenna connection. This wil
No I don't but there will be a small rg174 cable going to it. I know the sub-receiver is on the top near the back. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Thanks Carl< I wil
Rick, That's very unfair of you to accuse the 6500 of being a broad band noise generator. I am an avid DX'er and seacrh for signals right at the noise level. My 6500 hears ever bit as well as my Omni
My N4PY software will allow you to use a Flex Knob or Tmate 2 with the Eagle or any other radio to give you a remote pod like the 302R. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.c
You just should not comment about things you don't now about. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 4/9/2014 3:40 PM, Rick - DJ0IP / NJ0IP wrote: Carl, I'm talking abou
Ok this is the test I just did. I used my Kenwood TS2000 as the receiver. I have a 6 position rotary switch that grounds the unselected positions. This switch is what I use to move my antenna farm fo
No, it means that when the list sent something to you, the message bounced back to the list. It usually means that your email carrier was rejecting messages. Carl Moreschi N4PY 58 Hogwood Rd Louisbur
No it's the other way around. When the list sends something to you, if it fails, the list calls it a bounce. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Hardly think it was a sc
Flex radio's new policy is to charge for a major revision, but not to charge for updates and fixes to current versions. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 4/10/2014
I get nothing but unsolicited glowing audio reports on my Flex 6500. And in the simple test I did comparing transmit noise generated on a band, it was at least 30 db less than my Omni VII. Carl Mores
I would say the 6700 is better than average. Most radios are lucky to be -30 dBc. Many are somewhat less than that. Of course the numbers change from one band to another. One of my IC-781s is 34 dBc
When I watch signals on a panadapter, even very strong ones, I have to say most SSB signals fall within 3 khz width. And when they are too wide, it's because their mic gain is too high. Carl Moreschi
Yes, you can easily run everything on one computer. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com 73, Barry N1EU Barry, this was for you! (hi) I asked Rob to add a bit more about
Oh, QSK on the latest FW is very nice. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com 73, Barry N1EU Barry, this was for you! (hi) I asked Rob to add a bit more about his experienc
The horsepower for the Flex 6000 series is all in the radio. You do need a good graphics card in order to keep up with the display part. The graphics card does not need to be a gaming card but it doe
He's getting no CW offset at all. I think something in the switching circuit to bring the CW trimmer into play is not working. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 4/2
There are several ways to add a panadapter to the Eagle. The least expensive is to get a softrock ensemble II. See the link below. http://fivedash.com/index.php?main_page=product_info&cPath=2&product
I'm not sure about the software you need if you go with the Softrock Lite II running off the 9 mhz IF. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com - R. Eric Sluder W9WLW Mike, G
Because relays don't cause receive overload problems when very strong signals saturate the pin diodes. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Kim N5OP "People that make mus