I had an Omni A series B and the warc mod added transmit for 10 mhz and transmit/receive for 24 mhz. It did not include 18 mhz at all since the IF was 9 mhz. 10 mhz receive was already on the radio.
If you want something that will sell, look at the Icom 7300 and go from there. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com I would respectfully disagree with you in part. Consid
In 17 years of selling my software, I have never seen such a strong response on a new radio as the Icom 7300. It must be breaking all kinds of sales records. Carl Moreschi N4PY 58 Hogwood Rd Louisbur
The 7300 is used as a comparison because it is selling better than anything else right now. I don't think it's a great rig but most hams love it for reasons that are not clear to me. Also, direct seq
I think you MUST go down the direct sampling route. That's the new state of the art and the Flex 6000 series shows how wonderful this method is. There are no birdies anywhere and with so much in firm
Making a new transceiver that uses superhetrodyne now would be like making a car that used a point ignition system now. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com -LeeWA3FIY ;
Radio Shack when they were in business. Some radio shack's still have old stock. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Where can I get one? 73, Puck W4PM _________________
That's why it's a good analogy! Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Making a new transceiver that uses superhetrodyne now would be like making a car that used a point ig
Have you done all 3 resets to the Orion? 1) Power off Orion. 2) Power On holding the VFO B LCK button. 3) Continue holding LCK button until the radio says "Battery Failure". 4) Power off Orion. 5) Po
Denton, The next step I would do is clean the contacts on the large cables that connect to the Orion front panel. After the covers are off the Orion, remove the screws holding the Orion front panel.
Yes, and I believe this was slightly different from Binaural receive. The idea was different pitch signals would seem to come from different directions. Low pitch was all the way to the left and high
I used the cardboard method. It was very easy and foolproof. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 1/22/2017 12:12 PM, Bwana Bob wrote: Yes, there are a couple of ways
Rick, I don't have that firmware. But I do not believe changing the FW will fix the problem. I believe that problem comes and goes with temperature variations. The fix is to get a filter to connect t
I thought the QST article for panadapters was very poor. It recommended using the IF to feed the panadapter. This is an archaic method. Today with the SDR receivers available such as SDRplay, much be
My software keeps both radios on the same frequency. It allows you to click on the panadapter display and have the radio instantly go there. And as you tune the radio, the panadapter radio will follo
Also there is the Ameritron 1306 that adds 6 meters and computer control to the 1300. I have one and like it. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Don't let the name fool
It's a good one. I have two of them. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com What else should I be looking at? Tnx 73 Rick, DJ0IP ___________________________________________
My N4PY Orion program will allow you to get all frequency information on HDSDR for SDRplay. I have a method to attach the SDRplay and share antennas with SDRplay. Carl Moreschi N4PY 58 Hogwood Rd Lou
Sounds like something changed on the bias for the finals. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 12/21/2016 2:07 AM, k7mks@comcast.net wrote: My Corsair I draws 9-10 amp
My N4PY Pegasus Plus software allows up to 5 different hardware or software devices to be hooked up to the Omni VII at the same time. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com