while working xf4ih i noticed my output power was down....about 250 watts !!! then i checked my drive ( omni6-v3) and it was 60-70 watts normal for driving the herc to 400- 500 + watts out. Antenna /
ken, tnx for the reply.. the fault lite is constantly lit , but verry dim,,, i thought it was not on , and therefore a clue to something else...' i did build the 100 watt pa for the elecraft... so i
At 01:31 AM 2/6/2004, Kreinberg, David wrote: hours, I used the 'Sweep' feature. It worked normally at first, but after using it a few times I noticed a problem. ............... I gave up after about
CHUCK. ,,, if you have any interst in qrp or kitbuilding , you should check out the web site for the FDIM four days in may ... which is thursday before dayton+ dayton..= 4 days in May. On Thursday AL
yes you can update the software, look on the back there is a rj45; and in the operator's manual, which is on the web, they talk about the ip address. AND THAT AD ... IS SAD ... I hope that ad is from
I wonder what it is that causes our TT reflector to have so many comparisons to the 7800 & K2 ???? I also watch both those reflectors. I own stuff from all three. My observations are that those guys
Mark, Usually my NB has an effect on powerline noise. Rarely it has NO effect on powerline noise. Depends on the pulse. My Icom 756P2 nicely portrays the noise on the Bandscope... very easily identif
Noel JUV has a Omni V to sell.... ask him in the AM.... bill Hello Dave!!! I would like to get details on the Omni V and the jpg.........73 NOEL W9EFL@aol.com ________________________________________
i noticed that since day one... engaging either the split or vox dims my lights. if you turn on both functions the dial gets even dimmer.... yet if you xmit at full power the lights don't dim with th
i noticed that since day one... engaging either the split or vox dims my lights. if you turn on both functions the dial gets even dimmer.... yet if you xmit at full power the lights don't dim with th
Does this mean the vac relay ?? If i gently rap the cabinet it comes back,,,, no qro cw qsk; mostly ssb S&P ... with under 2-1 swr & tx/rx enabled set up with omni 6+.... is it worth reversing the re
interesting.... used titan 1 $1400 about a 1 a watt used herc II $ 900 about 1.80 a watt oops add a ps ...$$.300-400... because tubes put out more watts !!!! ???? bill SGC SG500 $2.60 per watt. PW1 a
IF THE FCC HAD ANY CONCERN AT ALL.... they would go get the guy who has 15 different ebay listings for " amateur" 300 watt amps... with no bandpass filtering....for cheapo...; He also sells mobile an
I WAS THINKING OF SELL ,,,,NOT ANY MORE.... great video , helps to appreciate my 6+ ( opt3ver)..... ALOT... reminded me I have a mute input on the back, which I bring up to my panel for PTT CW!!!! ..
i think it all goes back to the concept : If I were to have bought the WRONG RIG.... I WOULD BE STUPID !!!! otherwise I would have bought the right rig. ... Or as we used to say in the hifi biz : I w
would that be tune or cw mode ??? bill Anyone have advice on increasing the power output on an Omni 6+?? My rig showing output of only 55 watts on any band. Seems the pot to increase power is located
after following the 'titan insight' thread i read about the PS caps going bad, causing a low reading.... yup, i wasn't nuts. Two weeks ago i wondered if it was looking low,,,, 2000 hi 1200 low... gue
My company was the ILL/WI rep company for APC back in the beginning years. You know the story, once the commission checks got big, they put on direct sales guys. Anyhow...there are some differences i
hello everyone.... since this is the TT reflector...and my Orion reflector, can we leave the IC7800 conversation to the ICOM reflector ? I suppose after it is priced & shipped, there will be an appro