Under Dxbase 2005 'Tools/Options/Users Options/Radio 1 Tab(or Radio2)' A) select TenTec under Manufacturer Window, select Orion565 under Model. B) Put a 'check' in the Connect Radio 1 Serial Interfac
This only drives the point that what is transferred to the Orions's subreceiver should be user selectable. All I want to transfer to the subreceiver is the frequency and maybe the mode. My biggest be
You got it Barry, Also, I do object for all the reciever modes/setup/whatever being transferred to the sub receiver. I want to set up my sub receiver the way I want and only have its frequency change
Please read Barry's text, second to last paragraph. I answered a question .... Please read my response, first line, Duane. I agreed with Barry's point. Being an engineering manager, one of the points
Rick, I like it; I could also use other Oooops buttons. Good Luck In the Contest. Ron.....NU1U --Original Message-- From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com] On Behal
The Heil solution works great with my Orion; it elminated RF into the microphone inputs. I get outstanding audio inputs from the folks I work. I use Heil pro headsets and RadShack microphone bodies w
Hi Duane, No PTT on any of the 4 Hiel based microphones. Ron .... NU1U Do you also use the PTT connections? Paul's words were that pin 2 should never be tied to chassis ground. That is essentially wh
Yeh, I had those problems with my Kenwood TS930 and Icom 775DSP..........Guess what? No software updates to fix those problems. Ron ....NU1U And, above all, enables manufacturers to release unfinishe
In a nutshell, I solved my RFI induced audio problem with the Orion and my Heil microphones by tying the Heil's Mic shield to both the Orion's audio ground and to the Orion's chassis connector in the
See my previous post on this subject. I solved my RFI induced audio problems with my Heil mics by tying the Heil's shield ground to both the audio ground and to the Chassis grouns Yep, the schematic
Jim, Thanks for the information. I believe that I will rewire the Heil (and the one I built) transition cable to do what you suggest. I do have some 'old time' balance mikes that I would like to try
Got my Orion in September of last year and have been updating it with the software changes. I would say that the Orion is one of the most 'reliable' rigs that I have owned so far (Especially when com
Still, I don't have those problems............. Ron.....NU1U I can understand Tom's concerns. At the same time it is my belief that something that is deemed "unreliable" is something that fails frequ
Well Said......... Ron........NU1U nk you. Unfortunately a great deal of what I have read is to me childish and a complete waste of the time it takes me to delete these messages. I am interested in c
But does the manual tell one how to update the software? Ron, NU1U yes you can update the software, look on the back there is a rj45; and in the operator's manual, which is on the web, they talk abou
My Verify function has never completed its task..... I've learned to disregard it (don't run it anymore) without any problems with the past updates. Ron ......... NU1U it stops at line 9280 (9272 on
Rick, After you installed the update program and then opened 'Update', did you click on 'Settings' and enter the comm. port that you are using with the Orion? Ron ....... NU1U When I try to run the d
Just what is the best way of getting WHITE paint (what kind) on the Orion's MIC, PH, and CW jacks on the lower left side of the front panel without getting it every other place. I've already stuck my
Goodness, what a messy scenario.............. User Interfaces; the Orion is one of the best for such a complex rig that I have come across. I quickly learned the Orion's interface and do not forget w
Software updates are available for Dxbase 2004 to control the Orion. Ron ....... NU1U Me thinks Jack may want to reconsider that. There are going to be alot of Orions out there in the hands of top dx