One thing for sure...If a new rig ain't got a bandscope....forget it. People are rapidly getting hooked. Steve N4LQ _______________________________________________ TenTec mailing list TenTec@contesti
Is that Sky SDR the same thing as the LNR Rig? They look very similar. http://www.lnrprecision.com/store/#!/LD-5/p/39885476/category=10468544 _______________________________________________ TenTec ma
Sounds to me like your power supply is bad. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Q1 is just a transistor switch that triggers the relay coil. If the relay is buzzing you must be putting ripple on it and that comes right out of your power supply, 13.8v. I don't see why changing ca
Measure the voltage across the relay coil and see if it's being hung up by voltage or just a mechanical problem. Can you pull the cover off the relay? Steve N4LQ _____________________________________
Good luck. PLL problems are the reason so many Omni VI's get sold for parts. :*) _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/
Once you get this figured out it would be a huge help to the TenTec community if you would write up your findings. I'm sure it would help others. I've dealt with a few PLL problems and information is
1,800 volts in an Orion!!! Better watch where you poke around! That board would be a good item for Orion owners to stock up on. _______________________________________________ TenTec mailing list Ten
A TenTec 240 is a 160 meter converter. I'm not aware of a TenTec dummy load with a built in fan. Are you sure of the brand? _______________________________________________ TenTec mailing list TenTec@
Maybe you could contact this seller and see if he's any help. http://www.ebay.com/itm/Ten-Tec-Model-240-KW-160-10-Meter-1500-W-Dry-Dummy-Load-for-Ham-Radio-Clean-/172447004562?hash=item2826a47792:g:B
For the calibration to be off equally in all 4 modes, usb, lsb rtty and cw, 4 bfo trimmers would need to be set equally incorrect. _______________________________________________ TenTec mailing list
Barry I fiddled with this on a Corsair II. The offset for it was 750 Hz for cw but on the O6 it would depend on your sidetone frequency setting. I would guess 1500 Hz for SSB +/-. I lost interest bec
I'm using an IC-7300 as the main rig. After getting it, my K3S was gathering dust so I sold it. I also had the Flex 6500, FTDX-3000, IC-7800, TS-590s, Omni 7, TS-950sdx, TS-2000, FT-2000, Omni VI+, F
Er....Neither can the Orion without external help from another SDR, computer and software. Blocky and lousy looking? Well it looks like a mini Flex to me. It can be difficult to photograph. I finally
Perhaps this video would help. The default is a "filled spectrum" which makes signals appear as colored blobs. You can change this to produce a nice trace of the color of your choice. https://www.you
Here ya go: https://www.youtube.com/watch?v=wa2GJ5Aq6io&feature=youtu.be The camera doesn't capture the sharpness of the display but believe me, it's totally in focus and very crisp. N4LQ ___________
You can get some effect by simply reversing the leads on one side of your headset. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.co
Dear Not True: I said SOME effect...Not SAME effect. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec