I want to buy a Ten-Tec 302, 302J, or 302R Remote Encoder/Keypad. Any color or condition is OK, as long as the rotary encoder circuit works. Tony W1OT _______________________________________________
Both are close in my Omni VII, but I'd like to be able to adjust them. Are there user-accessible adjustments for them? I would use WWV for frequency and an Elecraft XG-1 for S-meter calibration, so I
Gary, According to a "Ten-Tec Instruction Sheet for Models 282, 285 and 288 Crystal Filters," they are designed for use in the Omni V, Paragon, Corsair and Corsair II transceivers. These are for the
MIke, I believe that the present specification for Omni VII output power is 100 W +/- 1 dB. I calculated this range to be about 125.9 W to 79.4 W. 73, Tony ___________________________________________
Yes, those last three are Collins mechanical filters for the Omni VII. 73, Tony W1OT _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.
Hi Paolo, I have had 2 Omni Vs, but I have not had your problem. I think there may be a part or solder joint in the crystal Y3 circuitry on the Xtal Osc-LO Mixer board that is bad sometimes. Or maybe
In the February 2008 issue of QST, on page 36, there is a reference to an internet article on this topic. The web address is not quite right. It should be (I hope I get this right): www.seed-solution
External receiver calibrators are available as Elecraft kits XG1 and XG2. They provide an output of either 50uV or 1uV into a 50-ohm resistive load. These levels correspond to S9 and S3 1/3 per the I
Bruce, There are 2 sheets about hiss reduction and AGC performance improvement mods that you can probably get from Ten-Tec that may be applicable to your Omni V. I don't know of an internet reference
Alan and Bruce, Yes, that is what I was referring to. 73, Tony _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/t
"... equal audio side tone output when going from speaker to head phones..." - I'd like to see that in the Omni VII, too. Tony W1OT _______________________________________________ TenTec mailing list
Rick, Various methods have been used to lower the Omni V's audio gain. If you go to www.tentecwiki.org and click on the site map and then 562audmod, you will find some info (which you may be aware of
Hi Paul, You will note on page 6-15 of the Omni V Operator's Manual that crystal Y2 and associated circuitry are used on both 80m and 20m. That might be a good place to start trouble-shooting. 73, To
Wayne, My Omni VII came with the Owner's Manual second release - August 2007. On its page 18, in describing the DC IN connector, it says, "The supply voltage can range from +12.8 to +15.0 Vdc but +13
Kevin, The Omni V also had an optional voice readout board, which gave the operating frequency only. The board description mentions the possibility of future additional features, but I don't know if
Most of the comments seem to center on a CW rig's receive characteristics. I like the Omni VII particularly for its freedom from transmitted chirp and clicks and for its adjustable rise/fall time. 73
Paul, I suggest that you click on and read "Choosing a Vertical" in the "Advice" box on the web page at www.bencher.com/ham/ . 73, Tony W1OT _______________________________________________ TenTec mai
Jim C, I did a Google search on "ten tec jupiter attenuator," and the first 2 listings were about attenuators that were stuck in the "on" position. Maybe this is the problem. Using maximum rf gain, y
Mike, I know this doesn't help, but you might have a filter that was made in the 43rd week of 1980. 73, Tony W1OT _______________________________________________ TenTec mailing list TenTec@contesting
Hi Martin, In any case, I wouldn't send the Orion back to Ten Tec if you couldn't tell them how to trigger the problem. I had a problem with my Omni VII that was intermittent, and I had a way that I