John asked me what response I'd gotten to my request about a Ten-Tec Omni V service manual, so I thought I'd follow up here for others to give feedback. I'm sure that such a thing must exist internal
John asked me what response I'd gotten to my request about a Ten-Tec Omni V service manual, so I thought I'd follow up here for others to give feedback. I'm sure that such a thing must exist internal
I too am still looking for a couple filters for my Omni V. I'd really like to get a 217, and I'd also kind of like to get a 282 as well, but the 217 is my higher priority. Getting back to the issue o
(My apologies, I'm re-sending this without the filter request, I didn't want folks to miss this part.) So here's a slightly crazy idea that nevertheless has some appeal to me. I have a proposal for t
Ten-Tec'ers, Having only received one positive response, and this being an idea that would require more than that participation to be able to fly, I guess this idea isnn't going to get off the ground
Reply to wb9iog: In case there is some confusion, the Omni V does have good basic documentation, including schematics and limited circuit description, but what I mean by a service manual is alignment
Well this has been quite interesting. I've surely received a wider variety of responses than I could have predicted (see below for a digested sampling). On balance however I (we) seem to be in the mi
Forgive me if this is too off topic, but its kind of related to Ten-Tec, because I'll now be legal to use my Omni-V once it comes back from the shop for a tune-up. I passed my 5WPM 1A test tonight! I
This is quite a group of folks. I received over 30 very nice messages of congratulations responding to my message about passing my 1A test. Too many to respond to all of you separately. The unanimous
Previous mention of practice keying an Omni VI got me to wondering if there is a similar method to practice key an Omni V? Thanks! - Tom _/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/ T
Steve, I assume you're referring to the TX-OUT and TX-EN jacks that have a jumper across them. I removed that and tried keying it and it does still have the sidetone, so that appears to be the soluti
My Ten-Tec Omni V has three filters in it that don't seem to bear the 2xx series model numbers that I find in all the listings of crystal filters, both at the Ten-Tec factory web site as well as the
Okay, I have another question for the marvelous collective experience in this group. I am still getting to know my "new" (to me) Omni V. The one control that most befuddles me is the Noise Blanker. I
Thanks for the explanations. That makes better sense now. Sounds like it is probably doing what it should. I've just got so much QRN most of the time with this temporary antenna setup that I haven't
Several people have contacted me independently for the answers that I received. I thought these had come across the reflector, but apparently not, so perhaps I should post them here for others who ma
I'm not familiar with this particular design, but being a designer of embedded control systems myself, generally this sort of thing would be handled as a circular buffer with some rule for replacemen
I looked up the X24C04 in my Xicor Data book. It is a 512 x 8 Electrically Erasable PROM with a 2 wire serial I2C interface. You read and write to it by sending and receiving serial packets with cont
I agree with AI2Q! I am pretty new to ham radio, but have had some helpful elmering from my dad who started building shortwave receivers 70 years ago at the age of 12 and built stuff all his life. Wi
Okay, here's something I've been wondering about that I'll be someone here knows about... I have several times seen ads reading like: "Send $10 for information and materials to turn your digital volt
This is something of an odd request, but I'm looking for a project box to build a VSWR / Watt meter project into. I'm wondering if any of you folks have some old surplus box that could be gutted and