*As you can see, it is basically Four independent power supplies in one case. Pay close attention to the 4 pin power plug for the Ten Tec Transceiver and the way that the 2 center pins turn the whole
*I am hoping that Gary, received the Manual which we emailed to him earlier today. My Gmail account sent it with no error messages. So we will wait and see if it was received. >>> 73 from Wade/KJ4WS
*Hello Guys,* * Wade here KJ4WS. First, Thanks Jim, for the vote of confidence. I believe that we also rebuilt the audio board for Ron's Argonaut Model 505. I still have the pictures where the small
*Your post came through just fine but, I believe that you were about 20 Hz low on frequency and had just a tiny bit of RF on your signal.... It may just be my eyes or this monitor?? >> 73 from Wade/K
*Thanks to an insider at Ten Tec who saved everything to a CD for me. We hope you enjoy the Ten Tec Model 564 Omni VI Plus Manual. Check your inbox ... >>> 73 from Wade/KJ4WS <<<* ___________________
*The choices? Sink with the Ship. Or jump ship before drowning. Is it really that bad at Ten Tec? None of the Insiders have said that there are any great problems.* __________________________________
*Everything should be Fine Business at your shack. From what we have seen so far the SS-30 is a very dependable power supply. I also missed the SS part of the model number. Sorry about that ...... >>
*Try Bob/K4TAX, he was one of the Beta Testers for Ten Tec on the Eagle and several other models. * rmcgraw@blomand.net *..... Bob, is a really great guy and any rig he sells will be in 110% working
*The manual you need, should be in an email from me. It is in .pdf format. Seems like I am moving lots of Bytes around here lately.* * 73 from Wade/KJ4WS* ____________________________________________
*That was a good bit of advise on the Low Pass Filter Board Joe. Mine was the small Pin Diodes that drive the relays. Mine had a really high SWR and pulled WAY TOO MANY AMPS on transmit. If the rig i
*Randy,* * Check out your inbox for the message from tvman1954@gmail.com <tvman1954@gmail.com> The 2 page schematic is all that I have. Sure wish that we could have been more helpful.... Just remembe
*Hello Gary,* * Wade here KJ4WS. Here is what I found after looking at the service manual. The 40 Meter Crystal is Y4. Sorry but I didn't go deep enough to get the frequency. You could have a bad cry
*Sorry guys, The long winded message should have been sent directly to Gary. * * 73 from Wade/KJ4WS* -- *Living one day at a time with Jesus as my Savior. But, still having Fun.* ____________________
*Thanks Barry,* * You made that poorly worded advise look really good. We can only hope that it helps others. * * 73 from Wade/KJ4WS* -- *Living one day at a time with Jesus as my Savior. But, still
*I believe that most of this problem, stems from the fact that the eye sees Red as much brighter. We know for a fact that the eye has more trouble at focusing when the color red is involved. This is
*This may not be the correct way to do it but, we used one of the small insulin syringes that my Miss Brenda, uses for her injections. * * 73 from Wade/KJ4WS* -- *Living one day at a time with Jesus
*Well my guess is that I am about to get really Slammed. We have used several OCF Antennas. At 100 Watts, things are pretty good. My problems appear anytime we try to go QRO. At a Kilowatt there does
*Hello Rick,* * You have a very good memory! I use the Ugly Balun ( about 12 feet of RG-8 wrapped around a 3 inch PVC Pipe ) this is a Current Balun. Although we don't like the loss from the Coax. We
*Once again I walk forward with my Asbestos Suit on hi .. hi .. In the QST Article linked below, modeled on a 66 foot dipole. The SWR and Loss Figures comparing Ladder Line ( Windowed Line ) and Coax
*Jon,* * The first thing that I would do is replace PIN Diodes D-1 thru D-8 .... These diodes were a very common problem " Back in the Day " You could also measure the forward voltage drop on these d