John - Don't you just need to take the end plastics off the panel and then just loosen the two top screws. The panel then will lean out and allow you to get inside to do things. You tried this, as pe
John - Thanks. I hadn't realized it would be sohard to get at to change the pot, but glad you made it. Sounds like you got the range you wanted. Congrats! Good luck and hope we can have a QSO one day
Curt - You checked with Ten-Tec? Don _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Brad - What is your email address. Wish to ask a question privately. Don, ve1bn@eastlink.ca _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.cont
Have you tried searching the Ten-Tec archives? Lots of info there. Don _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/li
Blair - Been searching for you re the finals, etc. Go Google and then search "TenTec argosy finals". At the bottom of this page, go to "more on this subject". The info you want is there. Don, VE1BN _
Puck - I had one built in '97 and it was the early model. Sold it. Try for one with a '99 production. These have surface-mounted components and no birdies and really work well. The last number in the
Ci - Your OMNI 6+ must have had factory improvements over the real early ones because you do not seem to have any problem with birdies, etc. Glad to hear it. 73 - Don, VE1BN _________________________
Joe - I have an excellent T-T #217 filter, like new, taken from a OMNI 6+. Give me your phone number or email address. Asking $55 US plus $5 mailing. Don, ve1bn@eastlink.ca __________________________
Alex - I have a spare TenTec #961 power supply. Unfortunately to ship it to Poland would be very expensive. It weighs approximately 6.6 kg but packed in a safe wooden crate would weigh about 9-10 kg
Understand you have to jumper two connectors on the back before you any RF out. Don - VE1BN _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.cont
John - I understand bias settings on both are the same. The finals are the same, etc. 73 - Don VE1BN _______________________________________________ TenTec mailing list TenTec@contesting.com http://l
Dale - Have you tried LOGic5, 6 or higher? I have been using this logging program for years and it does everything you want, auto-log of freq, bands, time on, and you can run the rig from the compute
Phil - Got fot the opt 3. 73 Don _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Jan - Thanks for the codes, but actually what is the process of putting these codes into use? In other words, how do you tell the rig? Don. ve1bn@eastlink.ca _________________________________________
money order in your money _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Javier - The service department for TenTec is (865)428-0364. Ask for Paul Clinton, the service manager. Buena suerte. 73 Don, ve1bn _______________________________________________ TenTec mailing list
I have for sale a mint Paragon II. It has just been updated at Ten-Tec. Full 100 Watt power output. This transceiver is in Medway, MA USA and boxed by Ten-Tec. Was always in a non-smoking environment
Hi Dave - Am curious. Can you send a pix through for that can soldering on the front end filter board you mentioned? Might clean up the very few weak birdies here, although they are not heard with th
Denny - Thanks for your advice. I am not the least bit concerned about the extremely weak birdies which I have to look for to hear at all. I am just curious what Dave Bowker has had done, that's all.