Mine is black and bluish white. Bob W2WG I recently took a picture to send to show another ham what the screen looks like. It was not turned on and it appeared to be green injthe picture. When it is
Can anyone tell me the hex code for narrow and wide cw for the Orion? N1MM can switch the filters from wide to narrow with a click on the bandmap. I have this set for SSB but have not figured it out
And to top it off, the encoder is a very cheap part. Supposedly TT had been replacing them with a more reliable version. Looks like you won the lottery. My condolences. 73 Bob W2WG First time I ever
Do you have an MW/HF signal generator of some sort? If so, the next time the received signals disappear but you still have noise, try sweeping the generator over its range with the Orion in SSB or CW
Without going through all the details--I had a similar issue and found that I had too long a power supply cable and too many unnecessary things in the line, all of which continued to voltage drops wh
Ralph Bob W2WG Here is the web site I use and it is still up. Best Regards, Raph Howes W8BVH http://www.qsl.net/tentec/ _______________________________________________ TenTec mailing list TenTec@cont
At the risk of reigniting a hot topic, this morning I developed a sudden SWR problem while running barefoot this AM. I was running 100W from my Orion 565 when I saw my digital meter jump up to around
Try grabbing the RIT knob, pull out fairly forcefully and rotate back an forth. This may or may not work and may or may not be a long term fix. Replacement of the encoder is the cure. It is doable at
As well as the original Orion. Bob W2WG It's good to see activity, but .. Too bad some of it isn't directed at the Orion II/v2 :( Grant/NQ5T _______________________________________________ TenTec mai
My Orion Classic is headed back to TenTec after successfully working he BS7 yesterday, going to sleep in good health, and waking up to total insanity after all manner of resets and clears, etc. I'm t
That is great news. Thanks for sharing it. Bob W2WG Tentec has been listening and is about to respond! I received the following in response to my request for information regarding the CW sidetone art
What I have done several times is to look on ebay for a used rocketport PCI card. These are UART based and designed for commercial POS applications. You will find 8 port versions with an external cab
My Orion I had been loaded with what I think was 2056. I was pretty satisfied with that release and had stayed away from later ones because of some of the issues reported on this reflector and some p
Jerry I have just sent additional information to TenTec which is essentially the same as you report, and had contacted the factory yesterday with initial information about it. I had not seen your ema
Carl I have seen your suggestion recommended. I have tried playing with the hang time with very minimal if any effect. I have also played with the threshold and decay time. No effect. A strange chara
Merle I spent most of yesterday playing with the new release again, wondering again if I have overlooked something. I hear the same things you do. I have run every AGC parameter through its ranges ma
Martin I can't comment directly on your case, but I had an Icom 756 with a line like yours--which would come and go. Then another line or two would show up and the original line would be gone--for a
I picked up my LP-100 fully assembled and calibrated from Larry at Dayton. What a nice device! After using it a few days I packed away an RF Applications digital meter and a nice RF Engineering analo
I don't have that here with 2062a. I am not using the bandscope, though. Bob W2WG Does any one have the same problem I have with V 2.062a? When I attempt to change bands or modes after a few minutes
Merle and Owen and Dick I have had the same problem several times--the no main RX part, that is. I don't use sweep. I had used the Orion (2.062a) this morning a little with no problem. I returned to