Ken, I use an external remote antenna switch. I have disconnected the coupling from the antenna switch on the 253 and use it as a section selector switch. I set it to Hi_SSB, Lo-SSB, CW and RTTY. Any
Jim, Glad you got it going. See you on the RTTY bands during contest times. Dave W7DPW MMTTY. resistor. RTTY two-stage with it. I Now, is fine _______________________________________________ TenTec m
Here's some info on Filter selection.. Dave W7DPW 04 E0 filter the crossed. The FILTERS VIA PROM to hear final) totally do. to be filter in about documentation, the users (watch it is not you off, se
I've had some problems with my Alpha 89 and SSB. Never on CW.. I use the keing loop. I believe my problem to be that the 89 is on the left side of my OMNI and causing a problem on key up .. Try movin
I have had my 253 for a number of years, in order to change its conditions, either the Tune button must be pressed, or the Antenna switch has to be changed. If you don't have it connected to the RS-2
I use a full 25 wire cable on my VI Plus, some of the other pins tell my 253 which band I am on.. Dave W7DPW signals in should frequency packet also these the to and out reflector years now. in my pr
I use a 25 pin cable from the computer to a y-cable,. One of the ends goes to the OMNI, the other goes to the 253. I similar situation exists when using the SS TT Linear.. Dave W7DPW for rig <tentec@
Pete, Would you just coat the coil on the 253 with DriSlide and let it dry or just the bearings ? I have a 253 that is a bit noisy.. Thanks, Dave W7DPW unprotected fingers. I shake the can and then s
There is shareware available to do that .. Do a search in Google for PDF995.. Dave W7DPW Hyder --N4NT-- Acrobat anyone wants _______________________________________________ TenTec mailing list TenTec
I thought that at pair of PDP-1170s running RSX-11M was very lightful.. Dave W7DPW _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.co
My 564, 6+, was received from factory on Nov 16, 1998, s/n 06A10508 Dave W7DPW _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/ma
I have found a filter , thanks Dave W7DPW _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
try , http://www.ac6v.com/telrex.htm Dave W7DPW ton doorknob _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/ten
Here's what AlphaPower says. You might want to investigate.. http://www.alpha-amps.com/html/ampkey.htm and for the OMNI VI plus: http://www.alpha-amps.com/html/tentec.htm Dave W7DPW -- Original Messa
Bob, Thanks for the information, I have been using the Y-Connection for the past 4-5 years with my ONNI VI plus and my 89 and haven't gotten any bad reports. I've also used the Loop. I'll have to lis
My invoice is dated 11/11/02 for SN TT-IØ58 Dave W7DPW amount paddle. were made? The one _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.
It's possible that the Amplifier relay is not turned off and than is what is heard. Dave W7DPW I start "amplifier _______________________________________________ TenTec mailing list TenTec@contesting
Sounds like the TxE (Etc) shunt is loose, try reseating it... dave W7DPW last night. band in any after the improvement. rest it. ask for _______________________________________________ TenTec mailing