For sale only within continental US, prices shipped to you via Fedex Ground, prepayment by USPS MO only. Ten-Tec 225 power supply (for Argosy); 7 out of 10 cosmetically, works fine $85 Ten-Tec 218 1.
I'm investingating a problem in my Omni VI type 563, possible diode failure in the antenna T/R path. The low-pass filter board (81592) shows three diodes in the main receive path from antenna to fron
Are there any issues to be aware of in changing the 1208 transverter to 10M IF other than substituting crystal to 22 MHz and changing tuned elements in the IF chain? Tks, Dave
Tried to remove front panel from Ten-Tec Scout (need to service something) and couldn't figure out how to fully separate the panel from the wiring and components behind. Anyone done this and know wha
A friend has lent me his new Omni 7 for a few days to check out, set up and generally make ready. While I was able to get the rfsquared.com remote software (with receive audio) working from a couple
Silly question but did you click the "Start RIP'n" button? 73, Alan N5NA Yes, but that's certainly a worthwhile question to ask!!!!! Hi Dave, You have to enable 6 UDP ports starting with the base por
Hi John, Success - I opened UDP 49154 and 49156 and receive audio is working fine. FYI I'm using it over a Verizon EVDO cell phone Internet service (basically a cell phone linked via bluetooth to a l
Looking for parts from Century 21 # 570 - the final amplifier section (anything from just the heatsink to a complete final amp module, need not be working or complete) and top/bottom covers (in any c
Downloaded and leafed through the programmers reference manual and have some questions about Omni VII remote IP streaming "RIP and TRIP". I haven't looked at the remote GUI code... 1. Is the audio en
For a project: Need final amplifier section (at least the heat sink, or as much as the whole subassembly), need not be working. Need top and bottom case sections (either/both), in any sort of shape (
Resurrecting a basket case Century 21 - need final amplifier section, any part or even just the heatsink, doesn't have to be complete or working. Also could use top/bottom covers, in any condition, p
I'm working on bring a Century 21 carcass back to life and I'm a little puzzled by the VFO dial mechanism - I thought the VFO was in need of rebuild, but it appears instead that the gears were not pr
Thanks Rick for the quick reply. I looked at the info there, and it helps, but I think what I'm struggling with is the function of the spring-loaded metal tab and it's gear - it presumably (when enga
Have an OMNI-D type 546, want to get WARC bands going. Here's my questions, per-band: 1. 10 MHz: Receives, goes into TX but no power out. Is this a jumper? Where? 2. 18 MHz: What is the Xtal freq? Or
Thanks very much! I've learned that I have a "series B" version of the Omni D, and understand the difficulties of enabling WARC. I was confused in part because the manual I received originally with t
Need manual/schematic for Ten-Tec 574 Century 21 (analog). Pls advise if you have copy available. (attempting to combine two dead units into one working one.) 73 Dave WB0GAZ wb0gaz@hotmail.com
The message seems to be clearer in the manual for the AT200PRO I just received - I use it with an old tube rig in one configuration (a QRP-ified Yaesu FTdx560, still able to max out at around 75W), a
Looking for advice: I am interested in a new (or at least new-to-me) HF rig, with the condition that it cannot consume more than 3A at 12V input. My first thought was the Ten-Tec 516 Argonaut (I've h
I'm doing a bit more research on the Ten-Tec 516. Could someone help me obtain this information: 1. What is the minimum input DC voltage for stable operation? 2. What is max current drain at 5W carri