- 1. [TenTec] 318 and 717 (score: 1)
- Author: John Henry <jhenry@tentec.com>
- Date: Wed, 1 Feb 2012 11:39:43 -0500
- I've had several emails requesting more info on the 318 and 717. They are on the website, and can be found by go to: www.tentec.com Type in the model number into the search box on the left side of th
- /archives//html/TenTec/2012-02/msg00008.html (6,922 bytes)
- 2. Re: [TenTec] 318 and 717 (score: 1)
- Author: John Sheeley <wb4qda@yahoo.com>
- Date: Wed, 1 Feb 2012 11:26:51 -0800 (PST)
- John Can we use verison 3 firmware on our Orion II with out installng tne new 2nd receiver ? 73 John wb4qda ________________________________ From: John Henry <jhenry@tentec.com> To: Discussion
- /archives//html/TenTec/2012-02/msg00009.html (8,528 bytes)
- 3. Re: [TenTec] 318 and 717 (score: 1)
- Author: Barry N1EU <barry.n1eu@gmail.com>
- Date: Wed, 1 Feb 2012 19:28:08 +0000
- absolutely - new subreceiver support was only a minor part of the new firmware Barry N1EU _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contes
- /archives//html/TenTec/2012-02/msg00010.html (9,395 bytes)
- 4. Re: [TenTec] 318 and 717 (score: 1)
- Author: Barry N1EU <barry.n1eu@gmail.com>
- Date: Wed, 1 Feb 2012 19:29:41 +0000
- after you load the v3 firmware, a question will pop up on the Orion screen asking if the RX366 is installed - you just say "no" (or "yes") and off you go Barry N1EU __________________________________
- /archives//html/TenTec/2012-02/msg00011.html (9,959 bytes)
- 5. Re: [TenTec] 318 and 717 (score: 1)
- Author: John Sheeley <wb4qda@yahoo.com>
- Date: Wed, 1 Feb 2012 11:33:04 -0800 (PST)
- thank you Barry 73 John ________________________________ From: Barry N1EU <barry.n1eu@gmail.com> To: Discussion of Ten-Tec Equipment <tentec@contesting.com> Sent: Wednesday, February 1, 2012 1:29 P
- /archives//html/TenTec/2012-02/msg00012.html (10,160 bytes)
- 6. Re: [TenTec] 318 and 717 (score: 1)
- Author: "TroyW6HV" <w6hv@verizon.net>
- Date: Wed, 01 Feb 2012 12:40:33 -0800
- I've ordered the RX366 (I expect it sometime next week), if I install the firmware now and answer "NO" to the receiver installed question. Would I then need to re-install the firmware after installin
- /archives//html/TenTec/2012-02/msg00013.html (10,297 bytes)
- 7. Re: [TenTec] 318 and 717 (score: 1)
- Author: Barry N1EU <barry.n1eu@gmail.com>
- Date: Wed, 1 Feb 2012 20:59:50 +0000
- I think you can just do a RAM Clear operation and you'll be presented with the question again. If for any reason that didn't work, you can always just reload the firmware. Barry N1EU ________________
- /archives//html/TenTec/2012-02/msg00015.html (12,049 bytes)
- 8. Re: [TenTec] 318 and 717 (score: 1)
- Author: "TroyW6HV" <w6hv@verizon.net>
- Date: Wed, 01 Feb 2012 13:13:13 -0800
- Thanks, Barry. I wanted to learn the new setup without waiting for the new receiver. Troy, W6HV I think you can just do a RAM Clear operation and you'll be presented with the question again. If for a
- /archives//html/TenTec/2012-02/msg00016.html (12,328 bytes)
This search system is powered by
Namazu