Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Corsair\s+II\s+Recieve\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Corsair\s+II\s+Recieve\s*$/: 6 ]

Total 6 documents matching your query.

1. [TenTec] Corsair II Recieve (score: 1): Author: "David N." <pkmaint@yahoo.com>; Date: Fri, 7 May 2004 08:59:49 -0700 (PDT); Hello All I have a Corsair II that the 160M Recieve falls off at the lower edge of the band Example: 1.9 mhz signal S9 same signal 1.825 S 3 but every thing above 1.9mhz seems ok to 2.0Mhz. My thinki; /archives//html/TenTec/2004-05/msg00134.html (7,374 bytes)
2. Re: [TenTec] Corsair II Recieve (score: 1): Author: "Ben K8DIT" <benk8dit@serv.net>; Date: Fri, 7 May 2004 13:04:59 -0700; David, It depends on what antenna you are using to listen on 160. It aslo depends on the matching device for that antenna. There are very few if any antennas that will maintain listening (or transmit; /archives//html/TenTec/2004-05/msg00142.html (7,325 bytes)
3. Re: [TenTec] Corsair II Recieve (score: 1): Author: "David N." <pkmaint@yahoo.com>; Date: Sat, 8 May 2004 19:28:48 -0700 (PDT); I am aware of the 160meter beast I have 800 ft. beverages but when it is the only rig that I own that looses its recieve at the lower end of the band where my ant. are cut for but not at the other en; /archives//html/TenTec/2004-05/msg00189.html (9,280 bytes)
4. Re: [TenTec] Corsair II Recieve (score: 1): Author: "Ben K8DIT" <benk8dit@serv.net>; Date: Sat, 8 May 2004 20:04:40 -0700; David, It's pretty clear if the mfj 259b is gone on the bottom of the band on your beverage then its an antenna problem not a rig problem. Or, did I read your note wrong? As for playing with the cors; /archives//html/TenTec/2004-05/msg00193.html (7,660 bytes)
5. Re: [TenTec] Corsair II Recieve (score: 1): Author: Bwana Bob <wb2vuf@qsl.net>; Date: Sun, 09 May 2004 09:33:33 -0400; Look at the underside of the bandpass board and check it for cold solder joints. This was a minor problem on some early Corsairs. The coil wires were a little tarnished and did not have good continui; /archives//html/TenTec/2004-05/msg00236.html (8,612 bytes)
6. Re: [TenTec] Corsair II Recieve (score: 1): Author: "David N." <pkmaint@yahoo.com>; Date: Sun, 9 May 2004 19:54:43 -0700 (PDT); Hello Bob Thanks for the advice. What do you think about Just Re soldering the whole board? Do you think it would have any adverse affects on the Tuning? Thanks David KR4OW -- Bwana Bob <wb2vuf@qsl.n; /archives//html/TenTec/2004-05/msg00239.html (9,486 bytes)

Current List: 1 - 6
Page: [1]