Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+More\s+Omni\s+D\s+problems\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+More\s+Omni\s+D\s+problems\s*$/: 7 ]

Total 7 documents matching your query.

1. [TenTec] More Omni D problems (score: 1): Author: tfr001@myfairpoint.net; Date: Wed, 26 Jun 2019 18:15:01 -0400; Hi all, More problems with my Omni D. It has this intermittent problem where both TX and RX will sort of go away... RX gets very deaf and TX goes very weak - only some mW output. It is somewhat sensi; /archives//html/TenTec/2019-06/msg00079.html (7,923 bytes)
2. Re: [TenTec] More Omni D problems (score: 1): Author: Mike Bryce <prosolar@sssnet.com>; Date: Wed, 26 Jun 2019 20:39:23 -0400; tom. have you looked at the reed relay on the output board? I had an Omni C do exactly the same thing. No TX and the rec was way off. The reed relay had its contacts fail Mike, WB8VGE www.theheathkit; /archives//html/TenTec/2019-06/msg00080.html (6,801 bytes)
3. Re: [TenTec] More Omni D problems (score: 1): Author: tfr001@myfairpoint.net; Date: Thu, 27 Jun 2019 17:48:45 -0400; Ding ding ding We have a winner... Mike, I assume you meant the "Hamlin" relay on the SWR board (inside the lowpass filter box) ? I just checked it. It is indeed a little flaky... sometimes makes con; /archives//html/TenTec/2019-06/msg00082.html (8,119 bytes)
4. Re: [TenTec] More Omni D problems (score: 1): Author: Mike Bryce <prosolar@sssnet.com>; Date: Thu, 27 Jun 2019 23:24:49 -0400; tom, I never could find a replacement. The factory doesnt have it anymore either. I took a SPDT reed switch, the glass switch, and extended its leads so I could make the necessary connections Slip th; /archives//html/TenTec/2019-06/msg00083.html (8,244 bytes)
5. Re: [TenTec] More Omni D problems (score: 1): Author: tfr001@myfairpoint.net; Date: Wed, 03 Jul 2019 16:08:14 -0400; Well, I wasn't able to come up with a reed relay to replace the bad one on my SWR board. I did, however, have some DIP reed relays around, and with a little hot melt and some jumpers, it seems to be; /archives//html/TenTec/2019-07/msg00007.html (7,358 bytes)
6. Re: [TenTec] More Omni D problems (score: 1): Author: w0ep <w0ep@w0ep.us>; Date: Thu, 04 Jul 2019 04:35:55 -0500; How is the noise level with a 50 ohm dummy load? Sent from BlueMail _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listi; /archives//html/TenTec/2019-07/msg00008.html (8,128 bytes)
7. Re: [TenTec] More Omni D problems (score: 1): Author: Peter Bertini <radioconnection@gmail.com>; Date: Thu, 4 Jul 2019 09:31:14 -0400; If the Omni has provisions for an external receive antenna, the first thing I would do is select the external RX antenna, and put an antenna on that RF connector. If the problem clears, then I'd look; /archives//html/TenTec/2019-07/msg00009.html (7,020 bytes)

Current List: 1 - 7
Page: [1]