Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+TT\s+omni\s+vii\s+if\s+port\s+problems\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+TT\s+omni\s+vii\s+if\s+port\s+problems\s*$/: 9 ]

Total 9 documents matching your query.

1. [TenTec] TT omni vii if port problems (score: 1): Author: denton sprague <denton@oregontrail.net>; Date: Thu, 30 Aug 2018 09:17:18 -0700; Hi allI installed an if port output as per 3 rivers TT omni vii dongle instructions to enable me to use a pc as a spectrum monitor. it works fine on receive but the minute I transmit, am told I am of; /archives//html/TenTec/2018-08/msg00205.html (6,884 bytes)
2. Re: [TenTec] TT omni vii if port problems (score: 1): Author: Bob McGraw K4TAX <rmcgraw@blomand.net>; Date: Thu, 30 Aug 2018 11:59:13 -0500; Do you have any application associated with the device controlling the radio? Also, if you are tuning to a signal using the dongle, it may be incorrect with regard to frequency thus this puts the Om; /archives//html/TenTec/2018-08/msg00206.html (8,818 bytes)
3. Re: [TenTec] TT omni vii if port problems (score: 1): Author: Greg S via TenTec <tentec@contesting.com>; Date: Thu, 30 Aug 2018 20:31:39 +0000 (UTC); Subject: Re: [TenTec] TT omni vii if port problems To: tentec@contesting.com Date: Thursday, August 30, 2018, 12:59 PM Do you have any application associated with the device controlling the radio? A; /archives//html/TenTec/2018-08/msg00208.html (9,633 bytes)
4. Re: [TenTec] TT omni vii if port problems (score: 1): Author: Bob McGraw K4TAX <rmcgraw@blomand.net>; Date: Thu, 30 Aug 2018 17:39:37 -0500; Largely because the dongle being used does not tune below or have adequate sensitivity below about 20 to 25 MHz. The IF in the Omni VII is about 70 MHz. 73 Bob, K4TAX On 8/30/2018 3:31 PM, Greg S; /archives//html/TenTec/2018-08/msg00209.html (10,749 bytes)
5. Re: [TenTec] TT omni vii if port problems (score: 1): Author: Greg S via TenTec <tentec@contesting.com>; Date: Thu, 30 Aug 2018 23:19:29 +0000 (UTC); Yes, but it can tune much HIGHER. Just so limiting using it as an I. F. Monitor only, in my eyes. Strokes for folks, I guess. Good luck getting it all sorted out. Greg, KC8HXO -- On Thu, 8/30/18, Bob; /archives//html/TenTec/2018-08/msg00210.html (12,778 bytes)
6. Re: [TenTec] TT omni vii if port problems (score: 1): Author: Carlos <carlos.peco@gmail.com>; Date: Fri, 31 Aug 2018 09:39:34 +1000; Hi Greg, I think it has to do with preselection and dynamic range. Most inexpensive (don't want to call them "cheap") SDR receivers for HF suffer due to strong broadcasters somewhere in the HF/MF ban; /archives//html/TenTec/2018-08/msg00211.html (14,565 bytes)
7. Re: [TenTec] TT omni vii if port problems (score: 1): Author: Bob McGraw K4TAX <rmcgraw@blomand.net>; Date: Thu, 30 Aug 2018 20:29:31 -0500; Even as a 2nd receiver, it is limited by the band pass filters in the front end of the Omni VII. As to using it in the IF, there is only about 2 MHz BW available from center frequency. I agree, u; /archives//html/TenTec/2018-08/msg00212.html (13,431 bytes)
8. Re: [TenTec] TT omni vii if port problems (score: 1): Author: Carl Moreschi <n4py3@earthlink.net>; Date: Thu, 30 Aug 2018 13:24:28 -0400; That won't put you off frequency. Do you have a logging program that is communication with the Omni VII? If it is not using RTS/CTS handshaking, it can cause the Omni VII to have an XIT value. You ha; /archives//html/TenTec/2018-08/msg00214.html (8,939 bytes)
9. Re: [TenTec] TT omni vii if port problems (score: 1): Author: Vic Klein via TenTec <tentec@contesting.com>; Date: Fri, 31 Aug 2018 04:24:55 -0400; I am using the same setup and like it very much. Are you listening to the audio from the computer instead of the rig? I usually mute the HFSDR, but if you are trying to listen on the computer you cer; /archives//html/TenTec/2018-08/msg00215.html (9,981 bytes)

Current List: 1 - 9
Page: [1]