Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+TX\s+EN\s+\&\s+TX\s+OUT\s+Jacks\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+TX\s+EN\s+\&\s+TX\s+OUT\s+Jacks\s*$/: 7 ]

Total 7 documents matching your query.

1. [TenTec] TX EN & TX OUT Jacks (score: 1): Author: w6ru@lightspeed.net (w6ru); Date: Sun, 20 Sep 1998 17:23:29 -0700; This is really confusing....what I see in the Omni 6 book (which has been mentioned here before several times) and what I measured at those jacks does not jive. I will do it again to make certain. Te; /archives//html/TenTec/1998-09/msg00352.html (7,414 bytes)
2. [TenTec] TX EN & TX OUT Jacks (score: 1): Author: paulc@mediaone.net (Paul Christensen); Date: Sun, 20 Sep 1998 20:27:20 -0400; TX OUT is an open collector, switching the ground. TX EN is the amp return line and it wants to see a mating open collector from a Ten-Tec amp. Without a Ten-Tec amp, the rear panel jumper must be in; /archives//html/TenTec/1998-09/msg00354.html (8,632 bytes)
3. [TenTec] TX EN & TX OUT Jacks (score: 1): Author: w6ru@lightspeed.net (w6ru); Date: Sun, 20 Sep 1998 18:41:34 -0700; Paul, Jim, and all, I made up a cable with a diode in series to connect the 87A "relay" jack line to a "Y" cable to plug into the "TX OUT" and "TX EN" jacks on the Omni 6 +. The polarity of the diode; /archives//html/TenTec/1998-09/msg00364.html (8,016 bytes)
4. [TenTec] TX EN & TX OUT Jacks (score: 1): Author: paulc@mediaone.net (Paul Christensen); Date: Sun, 20 Sep 1998 21:54:53 -0400; Great news Terry. Thanks for sharing this as an alternative with the rest of us. I'm sure you'll get plenty of questions on this and you may want to post some simple step-by-step instructions for tho; /archives//html/TenTec/1998-09/msg00365.html (9,287 bytes)
5. [TenTec] TX EN & TX OUT Jacks (score: 1): Author: jreid@aloha.net (Jim Reid); Date: Sun, 20 Sep 1998 16:43:11 -1000; Aloha Terry! Ref you note and test results on below: Thank you for your perseverance and tests. Wow, tomorrow I shall set up such a circuit, external to both the Omni and 87A. I read your solution to; /archives//html/TenTec/1998-09/msg00366.html (8,630 bytes)
6. [TenTec] TX EN & TX OUT Jacks (score: 1): Author: zeitler@ibm.net (zeitler@ibm.net); Date: Sun, 20 Sep 1998 20:45:11 -0700; --Original Message-- From: Jim Reid <jreid@aloha.net> To: w6ru <w6ru@lightspeed.net>; Paul Christensen <paulc@mediaone.net>; tentec@contesting.com <tentec@contesting.com> To: <tentec@contesting.com>; /archives//html/TenTec/1998-09/msg00370.html (9,905 bytes)
7. [TenTec] TX EN & TX OUT Jacks (score: 1): Author: w6ru@lightspeed.net (w6ru); Date: Sun, 20 Sep 1998 21:07:18 -0700; Jim, You stated "bands". The diode I used was a SK3081...your 1000 volt, 2 1/2 amp variety. I used this diode because I have them in large quanity. These only have one band on them and yes goes towar; /archives//html/TenTec/1998-09/msg00371.html (8,466 bytes)

Current List: 1 - 7
Page: [1]